Reznor HRPD Parts Manuals - Manual (Page 8)

Form P-RG/RP/RBL, P/N 263984R4, Page 8
Code 2 - Freezestat, J/C
#AI9AAF-2C, 25-225 o F,
P/N 126170, (replaces
P/N 16108)
Electrical Components - See location drawings on pages 6-7.
Code 1 - Electrical
Box and Cover (in the
electrical compartment)
Electrical Box, P/N
100108 (replaces 11965
on Model RG)
Electrical Box Cover,
P/N 100109 (replaces
P/N 9546 on Model RG)
Code 3 - Combustion Air Switch -
Replacement depends on date of
manufacture and altitude:
For power vented models mfgd beginning
7/04, altitudes to 4000 ft, P/N 204327, setpoint
0.58 ± .05" w.c. ; altitudes above 4000 ft , order
P/N 204328, setpoint .52 ± .05" w.c.
For RP Series units mfgd between 12/91 and 7/04 (except
RP/RPB Models with Option AG39/40 or 1st furnace of Models
HRPD/RPBL with Option AG41/42 modulating gas controls),
for altitudes to 4000 ft, order replacement kit P/N 193810; for
altitudes above 4000 ft , order P/N 193811.
For RP/RPB Models mfgd between 12/91 and 7/04 with
Option AG39/40 and 1st furnace of Models HRPD/RPBL
with Option AG41/42 gas controls, order P/N 193813 for
RP(B) Sizes 125-225 and HRPD 250-400 or PN 193812 for
RP(B) Sizes 250-400, HRPD 500-800, and all RPBL .
For all RP Series Models manufactured prior to 12/91 (serial
No. Date Code AQL), order Replacement Pressure Switch Kit,
P/N 93033.
Codes 4 & 39 - Firestat,
Honeywell #L4029E 1029,
Manual reset
opens at 200°F,
P/N 42782
Firestat Gasket, P/N 121041
(used when firestat is installed
less cover)
Firestat Shield, P/N 120021
(used with discharge firestat only)
Location and Components for
Installing Discharge Sensor,
Code 7A
Code 6 - Discharge Sensor
for Modulating Gas Valve,
P/N 48041, Maxitrol TS-121,
for Options AG8 & AG9; P/N
133228, Maxitrol TS-194 for
Options AG39 & AG41
Code 7A - Two-Stage
Ductstat, Honeywell
T678A1015,
P/N 41700
55-58°F,
Capillary
Length 5' -
Used in
Gas Control
Options
AG3, AG4,
and AG5
Bulb Holder, P/N 100260
Cable Strap, P/N 16227
Code 7B - Ductstat Sensor and Holder
for Code 7C Remote Ductstats
Ductstat Sensor Holder,
#TE6001-1, P/N 115850
Ductstat
Sensor only,
#SET A99BC-25C, P/N 115851,
(part of P/N 115848 below)
Code 7C - Remote Ductstat Modules in
Gas Control Options AG15-AG20
A = Ductstat Temperature Selector Module,
J/C A350AA-1C, P/N 115848
B = Stage Adder Module, J/C S350AA-1C,
P/N 115849
C = Digital Temperature Display Module,
J/C D350AA-1C, P/N 115852
Gasket,
P/N 104138
Bulb Clamp,
P/N 100260
Ignition Controller for Intermittent
Spark Pilot System without Lockout,
P/N 257009 (Serial No. Code 94)
Ignition Controller for Intermittent
Spark Pilot System with Lockout,
P/N 257010 (Serial No. Code 95)
To replace a
previously used
recycling ignition
controllers without
lockout (Serial No.
Codes 62 and 66),
order Replacement
Kit, P/N 257472
To replace a
previously used
ignition controllers
with lockout
(Serial No. Codes
63, 65 and 84),
order Replacement
Kit, P/N 257473
Sheetmetal
Retaining
Plate,
P/N 7727
Element Bracket
P/N 100260*
Cabinet
Leg
Gasket,
P/N 7726
Capillary
*Element bracket
P/N 100260 is for
CODE 7A, P/N 41700,
manufactured by
Honeywell. If using a
CODE 7A, P/N 41700,
manufactured by
Essex Corporation,
the element bracket
P/N is 104156.
(Entrance
in ductwork)
Grommet Clamp,
P/N 131993; Cable
Clamp, P/N 132065
Code 5 - Ignition Controllers
A B C