Futaba 12Z - Manual (Page 61)

61
PUSH
[Cursor Lever]
Ɣ0RYHPHQWRQWKH
VFUHHQGLUHFWLRQV
Ɣ3XVKWKHOHYHUWRFDOO
QH[WSDJH
[Data Input Dial]
[Enter Button]
[Return Key]
Ɣ7RKRPH
VFUHHQ
Ɣ7RSUHFHGLQJ
VFUHHQ
THROTTLE CUT
6WRSVWKHHQJLQHVDIHO\DQGHDVLO\DLUSODQHDQGKHOLFRSWHURQO\
Throttle cut provides an easy way to stop the
HQJLQHE\ÀLSSLQJDVZLWFKZLWKWKHWKURWWOHVWLFN
at idle. The action is not functional at high throttle
to avoid accidental dead sticks. The switch’s
location and direction must be chosen, as it defaults
to NULL.
Throttle cut setting procedure
*Perform the following settings before using the cursor lever
to move the cursor to the item to be set.
$FWLYDWHWKHIXQFWLRQ
0RYH WKH FXUVRU WR WKH >$&7,1+@ LWHP DQG
WXUQ WKH GDWD LQSXW GLDO WR WKH OHIW XQWLO WKH
EOLQNLQJFKDQJHVIURP,1+WR21RU2))
DQGWKHQSXVKWKHHQWHUEXWWRQ
6ZLWFKVHWWLQJ
0RYH WKH FXUVRU WR WKH >6:,7&+@ LWHP DQG
FDOOWKHVZLWFKVHWXSVFUHHQE\SUHVVLQJWKH
HQWHU EXWWRQ DQG VHOHFW WKH VZLWFK DQG 21
GLUHFWLRQ
(For a detailed description of the setting method, see [Switch
Setting Method] at the back of this manual.)
7KURWWOHFXWSRVLWLRQVHWWLQJ
0RYH WKH FXUVRU WR WKH >&87 3RV@ LWHP DQG
DGMXVWWKHVHUYRRSHUDWLRQSRVLWLRQDWWKURWWOH
FXWRSHUDWLRQE\WXUQLQJWKHGDWDLQSXWGLDO
WRWKHOHIWRUULJKW
,QLWLDOYDOXH
$GMXVWPHQWUDQJHa
(When the enter button is pressed, the servo operation
position is reset to the initial value.)
*With the selected cut switch ON and the throttle stick at idle;
adjust the rate until the engine consistently cuts off.
However, be sure that the throttle linkage does is not pulled
too tight and unreasonable force is not applied to the servo.
ŏ 6HOHFW >7+5277/( &87@ DW WKH OLQNDJH PHQX DQG
FDOOWKHVHWXSVFUHHQVKRZQEHORZE\SXVKLQJWKH
HQWHUEXWWRQ
ﶬﷄﶰﶶﶬﶬﶼ﷊ ﵺ ﷎ﶪﶬ
ﴶﴸﴸﳜ
﷒﷎ﶬﵼﷂﶸﷄ Ｂ８Ｄ
ｄＸﻪ ﷎ﶪﶬ ﵺ ﶴﶶﶮ
８＊＜＜ ﶮﶦﷂﶬ﷎ﷄ
ﹼ﹘﹚
﹢﹤﹜ﹰ﹚ﹰ﹤﹦ ﷤﷦﷦ﶊ
﷦ﶊ
ﶮ﷊ﶬﶬﷂﶸﷆ
ﶰ﷒ﶸﷆ﷊
﷜﷦ﶊ
ﷄﷂﷆﷄ
ﶼﶶﶦ
ﶺﶶ﷌﷊ﶼ﷤ ﷎ﶶﶸ﷌ﷂﶬ﷤
ﴶﴸﳰﴶﴸﳰﴸﴸ
ŏ&XUUHQWWKURWWOHSRVLWLRQ ŏ&XWSRVLWLRQ