Futaba 12Z - Manual (Page 122)

122
Curve setting operation
This section describes the setting procedure of curves which are used with the AFR function and each
PL[LQJIXQFWLRQ
Curve type selection
6L[W\SHVRIFXUYHVOLQHDU(;3(;3975OLQHDQGVSOLQHFDQEHVHOHFWHG
Curve type selection
1. Use the cursor lever to move the cursor
(reverse-video) to the [MODE] item.
2. Display the curve you want to use by
turning the data input dial to the left or
right.
*The curve type blinks.
:KHQ WKH HQWHU EXWWRQ LV SXVKHG WKH
curve type is changed. (Operate another
key to stop the change.)
[LINEAR]: Linear curve
[EXP1]: EXP1 curve
[EXP2]: EXP2 curve
>975@975FXUYH
[LINE]:
Line
[SPLINE]: Spline
Linear curve (LINEAR) adjustment
The curve left and right rates ([RATE A],
[RATE B]) can be adjusted separately.
The curve can also be offset horizontally
([OFFSET]) in the vertical direction and the rate
UHIHUHQFHSRLQWFDQEHRIIVHW>;2))6(7@WR
the left and right.
[Rate setting]
1. Use the cursor lever to move the cursor
(reverse-video) to the [RATE A] or [RATE B]
setting item.
2. Set the rate by turning the data input dial
to the left or right.
Initial value: +100.0%
Adjustment range: -200.0~+200.0%
(When the enter button is pressed for 1 second, the rate is
reset to the initial value.)
Setting by curve type
When the curve type is selected as described above, adjustment items corresponding to the curve type
appear on the screen. Adjust each curve as described below.
[Offsetting the curve horizontally in the
vertical direction]
1. Use the cursor lever to move the cursor
(reverse-video) to the [OFFSET] setting
item.
2. Move the curve in the vertical direction
by turning the data input dial to the left or
right.
Initial value: +0.0%
(When the enter button is pressed for 1 second, the curve is
reset to the initial value.)
[Offsetting the rate reference point to the left
or right]
1. Use the cursor lever to move the cursor
(reverse-video) to the [X OFFSET] setting
item.
2. Offset the curve reference point to the left
or right by turning the data input dial to
the left or right.
Initial value: +0.0%
(When the enter button is pressed for 1 second, the
reference point is reset to the initial value.)
﷒﷈ﶰ ﵺ ﶈ﷌ﵼﶰﶆ ﴶﴸﴸﳜ ﶺﶶ﷌﷊ﶼ﷤ ﷎ﶶﶸ﷌ﷂﶬ﷤ ﴶﴸﳰﴶﴸﳰﴸﴸ
＜Ｂ８ＪＲ０
ﻤｄｆｆﻞｆ
ﴌﴈﴞﴜ
ﴂﴤﳾﴜ ﳌ ﴤ ﴂﴤﳾﴜ ﳌ ﴢ
ﻤｄｆｆﻞｆ
ﻚﻚ ﻤｆﻞｆ
ﴈﴚﴚﴀﴜﳾ
ﻚﻚ ﻤｆﻞｆ
ﳶ ﳌ ﴈﴚﴚﴀﴜﳾ
ﳖﴶﴮﴸ
ﳖﴶﴸﴸ
ﳖﴮﴸ
ﴸ
ﳒﴮﴸ
ﳒﴶﴸﴸ
ﳒﴶﴮﴸ
ﴆﴈﴀ
ﳖﴸﳐﴸ ﳖﴸﳐﴸ ﴂﴤﳾﴜ
ﴠﴖﴰ
ＲＢ＜
ﴘﴂﴆﳎﴀﴊﴘ
ﷆﶰﶶﶪﶴ
ＲＨ０
1RWH :KHQ \RX FKDQJH WKH FXUYH W\SH
the preset curve data in the function
is cleared. Be sure that you don’t mind
losing this data.