Digilent 410-273P-KIT - Manual (Page 14)

WF32 Reference Manual
Copyright Digilent, Inc. All rights reserved.
Other product and company names mentioned may be trademarks of their respective owners.
Page 14 of 24
alternate position for JP3 is the SS position. The digital pin number for the microcontroller signal SS is 44. With JP3
in the SS position, digital pin 44 is connected to the pin labeled 10 on the board, and digital pin 10 is not
connected.
The pin labeled 10 on the board is connected to connector J7 pin 5. This is shown as J5-05 in the following tables.
In the ‘Pinout Table by Shield Connector Pin’ table below, J5-05 is shown has being either chipKIT pin # 10 or 44.
J5-04 is connected to chipKIT pin # 10 when JP3 is in the PWM position and is connected to chipKIT pin # 44 when
in the SS position.
Pinout Table by ChipKIT Pin Number
ChipKIT
Pin # MCU
Pin Port
Bit
PIC32 Signal Name Function
0 52 RF02 SDA3/SDI3/U1RX/RF2 GPIO, UART
1 53 RF08 SCL3/SDO3/U1TX/RF8 GPIO, UART
2 18 RE08 AERXD0/INT1/RE8 GPIO, external INT
3 72 RD00 SDO1/OC1/INT0/RD0 PWM 1
4 88 RF01 ETXD0/PMD10/RF1 GPIO
5 76 RD01 OC2/RD1 PWM 2
6 77 RD02 OC3/RD2 PWM 3
7 19 RE09 AERXD1/INT2/RE9 GPIO, external INT,
USBOC INT
8 66 RA14 AETXCLK/SCL1/INT3/RA14 GPIO, external INT
(shared with
P32_USBOC)
9 78 RD03 OC4/RD3 PWM 4
10 81 RD04 OC5/PMWR/CN13/RD4 PWM 5 (JPR to
digital pin 10
position)
11 12 RG08 ERXDV/AERXDV/ECRSDV/AECRSDV/SCL4/SDO2/U3TX/PMA3/CN10/RG8 SPI_SDO
12 11 RG07 ECRS/SDA4/SDI2/U3RX/PMA4/CN9/RG7 SPI_SDI
13 10 RG06 ECOL/SCK2/U6TX/U3RTS/PMA5/CN8/RG6 SPI_SCK, User LED
LD6
14/A0
23 RB02 AN2/C2IN-/CN4/RB2 AIN0, GPIO
15/A1
21 RB04 AN4/C1IN-/CN6/RB4 AIN1, GPIO
16/A2
32 RB08 AN8/C1OUT/RB8 AIN2, GPIO
17/A3
25 RB00 PGED1/AN0/CN2/RB0 AIN3, GPIO
18/A4
34 RB10 AN10/CVrefout/PMA13/RB10 AIN4, GPIO
19/A5
35 RB11 AN11/ERXERR/AETXERR/PMA12/RB11 AIN5, GPIO
20/A6
22 RB03 AN3/C2IN+/CN5/RB3 AIN6, GPIO
21/A7
20 RB05 AN5/C1IN+/VBUSON/CN7/RB5 AIN7, P32_VBUSON
22/A8
33 RB09 AN9/C2OUT/RB9 AIN8, GPIO
23/A9
24 RB01 PGEC1/AN1/CN3/RB1 AIN9, GPIO