Setting your energy saving programs – Braeburn 5200 User Manual

Page 6

NOTE: If the 7 day programming mode was selected during the Installer Setup

(section 3), the default program will use the weekday times and temperatures

shown above for all 7 days. The programming mode can be switched between

weekday-weekend and 7 day at any time by programming the Installer Options

(see section 3).
• Make sure you place the system switch in the

HEAT or COOL modes of operation

as appropriate. You should not enter a program in the

OFF or EMER position.

• When you place the system switch in the

COOL or HEAT modes of operation,

the appropriate indicator will also appear in the LCD display when the system
is running.
• When you place the system switch in the

OFF mode the display will indicate OFF.

Programming Overview For 7 Day Programming Mode
The 7 Day mode has separate Whole Week or Individual Day programming to allow
you to change the daily set point times and temperatures to meet your individual
schedule needs. The Whole Week programming can be used to set the main
portion of your schedule, allowing you to later modify speciﬁc days of the week as
required using the Individual Day programming capabilities.
Whole Week - allows you to program all seven days (M, TU, W, TH, F, SA, SU will
show in display) at the same time. Then you can use individual day programming
to ﬁne tune your program for the few set point times or temperatures that you may
wish to change.
Individual Days - allows you to program each day of the week individually to give
you the greatest schedule ﬂexibility. Often used to ﬁne tune programming after
initially programming.
IMPORTANT NOTE! When in Whole Week programming, the thermostat will

check if all of the days of that group have the same program set point times and

temperatures. If so, the set point time and temperature of the individual set point

will be displayed. Otherwise, the individual set point time and temperature will be

blanked. The user is allowed to change the daily programs for this set point time

and temperature by pressing the or button. This will reset all the daily

programs of the group for that specific individual set point time and temperature to

the startup default for that set point. Continued pressing of the or button by the

user will change set point time and temperature settings as desired.

cont.

Setting Your Energy Saving Programs

Entering Your Program – Weekday / Weekend Mode (5-2 Day)
1. Place the system switch in the HEAT
mode of operation.
2.

Press the

PROG button to enter the Program

setting mode. The

MORN set point of the

Whole Week Program Group will be
displayed. The display will show

M, TU, W,

TH, F, SA, SU to indicate the whole week
is being programmed. The hour portion of the set point time and the

AM/PM

indicator will be ﬂashing.
3. If you wish to program each day individually press the DAY/TIME button to

select each day.
4. Press the or button to change the time to the desired hour in one hour

increments. Press

PROG button, the minute portion of the set point time will

begin ﬂashing.
5. Press the or button to change the time to the desired minute in 10-minute
increments, press the

PROG button. The temperature digits will begin ﬂashing.

6. Press the or button to change the set point temperature to the desired

setting in 1˚ F increments (0.5˚ C). Press the

PROG button.

7. Follow steps 4 through 6 to set the set point times and temperatures for the

DAY, EVE and NIGHT for the HEAT mode.

8. Place the system switch in the COOL mode of operation. The display will show

COOL. Follow steps 2 through 6 to set the set point times and temperatures for

the

COOL mode.

9. After completion of programming, wait 30 seconds or press RETURN to return
to the normal mode.

Programming Overview For Weekday/Weekend Programming Mode (5-2 Day)
Your thermostat contains separate Weekday and Weekend Program Groups that
allow you to change the daily set point times and temperatures to meet your
individual schedule needs.
Weekday - allows you to program all the weekdays (M, TU, W, TH, F will show in
display) at the same time. Allows programming times and temperature settings
for four set points (MORN, DAY, EVE, and NIGHT) to meet your daily weekday
schedule needs.
Weekend - allows you to program all the weekend days (SA, SU will show in
display) at the same time. Again, allows programming times and temperature
settings for four set points (MORN, DAY, EVE, and NIGHT) to meet your daily
Weekend schedule needs. (Continued on page 12)

cont.

Setting Your Energy Saving Programs