Braeburn 5200 - Manual (Page 3)

4 5
Programming Installer Settings
3
cont.
When the User RESET button is pressed, the following options will reset to the
factory defaults. All other settings are saved when the RESET button is pressed.
Function Status After RESET
Programming Default setting depending on programming mode
setting (see Section 4). For manual mode:
Heat - 62° F, Cool - 83° F.
Clock 12:00 p.m., Monday
1st Stage Differential 0.5° F (0.25° C)
2nd Stage Differential 2° F (1.0° C)
Filter Check Monitor 0 days-off, Time reset
Keypad Lock Unlocked
Temperature Hold
Permanent and Temporary Hold Cleared,
Reset to Long Hold
Short Cycle Protection Timer On, Reset
Programming Installer Settings
3
cont.
Setting Thermostat Installer Options
The Installer Options section allows the system and programming parameters
to be set up at installation. The Installer Options mode is menu driven. As the
different options are programmed you may eliminate specific options. For
example, if the system is set to single stage heat pump in Option 3, the selection
for first stage fan control will no longer be available.
To enter the installer settings mode:
Press and hold the RETURN and buttons at the same time for 3 seconds until
installer option 1 (Programming Mode) is diplayed. Pressing the or buttons will
scroll between choices. To scroll to the next installer option, press the RETURN
button. To scroll backwards, press the PROG button. The thermostat will return to
normal operating mode after the last Installer Option mode has been set or by
pressing the RETURN and PROG buttons at the same time.
NOTE: The thermostat will return to normal operating mode automatically after
30 seconds if no key is pressed.
NOTE: Any changes to Installer Option 3 (System Type) will cause Options 4, 5, 6,
9 and 10 to reset to the default values that are dependent on system selection.
Any changes to Installer Options 1 or 11 will cause all User Options and
Programming to reset to their default values if the User Options were previously
programmed. See Section 5.
Installer Options Factory Default Option Comment
1 – Programming pro7 pro7, pro52 Selects the programming mode:
Mode
proNO
7 day, 5-2 day or non-prog.
2 – Enable / Disable recOF recON, recOF Enables or disables early recovery.
ARM TM Not available in non-prog. mode.
3 – System Type 11
C
11
C,
22
C,
11
HP
Selects single stage conventional,
22 HP 2 stage conventional, single stage
heat pump or 2 stage heat pump.
4 – First Stage 1 H6 1 H6, 1 HE Not available with a heat pump
Fan Control system. Selects between 1st stage
gas or electric heat.
5 – Second Stage 2
HE
2
HE,
2
H6
Only available with a 2nd stage
Fan Control heat pump system.
6 – Fossil Fuel au HE au HE, au H6 Only available with a 2nd stage
Backup Option heat pump system. Locks out 1st
stage during 2nd stage heat call
for fossil fuel back-up system
(AUHG) With an electric back-up
system (AUHE), both stages will run.
7 – Residual Cooling fan60 fan00, fan30, Selects 0, 30, 60 or 90 seconds as
Fan Off Delay fan60, fan90 the time the fan will stay on after
the cooling system has satisfied the
set point temperature and has
turned off the compressor.
8 – Short Cycle sspON sspON, sspOF Selects SSPON (5 minutes) or
Protection SSPOF (off) for the compressor
short cycle protection.
9 – Compressor copOF copOF, copON Only available with 2nd stage
Power Outage heat pump and AC power
Protection connected. Select between
compressor lock off or
compressor lock on.
10 – AC Power aciOF aciOF, aciON Only available when thermostat
Interrupt Warning is installed as a hardwired unit.
Select between turning the AC
power interrupt warning off or on.
11 – Temperature de 6 F de 6 F, de 6 C Selects either Fahrenheit
Scale or Celsius.
Description of Options
1. Selects the programming mode, either full 7 day or 5-2 day
(weekday-weekend) programming or non-programmable.
2. Enables or disables the ARM™ feature. During ARM™, room temperature is
recovered gradually by turning on the heating or cooling before the end of the
set back period. In a multi-stage configuration, room temperature is recovered
gradually by using only the first stage heating or cooling until the last 20
minutes, to minimize the use of the 2nd stage heating or cooling. The set
point temperature is changed to that of the upcoming comfort program
temperature. ARM™ does not operate when the unit is in the temporary or
permanent HOLD mode if the program is temporarily overridden or if
emergency heat is selected for multi-stage heat pumps. If the ARM™ feature
is disabled the thermostat will recover the set point temperature at the
programmed set point time after the setback period ends. (continued on page 6)