Panasonic WV-CM143 - Manual (Page 6)

STANDBY-GND Connection
The connected buzzer or chime will sound when
the Mode Selection Switch is positioned at
STANDBY and the intercom or alarm is activated,
ALL MODE-GND Connection
The connected buzzer or chime will sound at
either position oi the Mode Selection Switch when
the intercom or alarm is activated.
REMOTE OUT Connection
The terminals for the Remote Out are used to con­
nect the Remote Out are also used to connect the
Spot Monitor Control In for the Spot monitoring by
short circuit of terminal 1, 2, 3 or 4 when the two
color monitor is connected with Remote Controi
Unit for Auto Panning Head.
The power rate of the alarm should be DC 24V,
max. 100 mA.
If the power capacity of the remote is less than
100 mA at DC24V, the remote load can be con­
nected at DC 24V, the remote load can not be
connected at the terminal directly. In this case, the
relay circuit should be used for the remote load.
22. Timing Select Output Connector
(TIMING SELECT, OUT)
This output connector produces the timing pulse sig­
nals for switching the sequence operation of other
extensible systems such as another Color CCTV
Systems or sequential switcher system,
23. Timing Select Input Connector
(TIMING SELECT, IN)
This input connector is provided for the sequence
operation with timing pulses from the time lapse VTR or
another Color CCTV System.
24. Audio Input Connector (AUDIO IN)
Accepts the audio signal from the video camera with
microphone.
You can hear the VTR sound by setting the Input
Selection Switch to the EXT position.
25. Audio Output Connector (AUDIO OUT)
The audio signal is supplied from this connector to the
VTR.
29. Camera Input Connectors (CAMERA INPUT, 1/2/3/4)
The BNC type connectors are used to provide the
video output signal of the cameras to the additional
video tape recorder.
This connector supplies DC power and vertical drive
pulse to the camera and receive the video informations
from the cameras.
Notes:
• Be sure to connect only the specified camera.
• Connect the camera after making sure that the
monitor is off.
When the camera is connected while the monitor is on,
the camera will not be functioned by activating the pro­
tection circuit for misconnection.
Caution:
The CAMERA INPUT 1 connector only can accept
the multiplexed VD (VD2) signal from the specified
Color Mini CCTV System Camera.
Even if the multiplexed VD (VD2) signal will be
supplied to the CAMERA INPUT 2, 3 or 4, this
monitor can not work correctly.
30. Camera Extension Input Connector
(CAMERA EXTENSION IN)
This is a 12-pin connector for the Camera Extension
unit when it is used for extending additional 3 cameras,
and the information are as;
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Pin 7
Pin 8
Pin 9
Pin 10
Pin 11
Pin 12
Logic Signal for Sequence
Logic Signal for Sequence
Logic Signal for Sequence
Video Input Signal
Ground
Logic Signal for Sequence
Logic Signal for Sequence
Logic Signal for Sequence
Logic Signal for Sequence
Logic Signal for Sequence
Vertical Drive Output Signal
DC Voltage for Cable Compensation
31. Screen Control
This control is preset at the factory.
Do not adjust this control.
When the adjustment of this control is required, refer to
the qualified service personnel.
26. Power Cord
Caution: 120V AC supply only.
32. Focus Control (FOCUS)
This control is preset at the factory.
27. Video Input Connector (VIDEO IN)
This is a video input connector from VTR for playback
picture.
When you would like to observe the VTR playback pic­
ture on this monitor, set the Input Selection Switch to
the EXT position and Mode Selection Switch to the ON
position.
28. Video Output Connector (VIDEO OUT)
The BNC type connector is used to provide the video
output signal of the cameras to the additional monitor
or video tape recorder.
The video output signal of the camera is provided from
this connector even when the Mode Selection Switch is
the STD BY position.
33. Camera Power On/Off Selection Switch
(CAMERA POWER, ON/OFF)
ON: Set this position to use with the specified Color
CCTV Camera.
OFF: Set this position to use with the specified Color
System Camera (Multiplexed VD (VD2) with gen­
lock).
No power supply to the camera.
Caution:
Be sure to set this switch before camera connec­
tion.
-4-