Qmark EFQ Series - Commercial Fan-Forced Wall Heaters - Manual (Page 4)

1. Rotate the thermostat(s) fully clockwise. This should energize
the heating elements and, after a short delay, engage the
fan causing warm air to flow from the hot air discharge at the
openings in the bottom of the grille.
2. After the operation check, rotate the thermostat(s) by inserting
a small screw driver through the grille to the desired position
to obtain room comfort. For units with two thermostats, it is
recommended that both should be set at approximately the
same setting.
NOTE: For best results, the heater should be left “ON” constantly
during the heating season because the thermostat, when properly
set, will maintain the desired temperature.
TO RESET MANUAL RESET LIMITS
Your heater is equipped with two manual reset safety thermal limit
controls that will automatically turn the heater off to prevent a fire if
the heater overheats. These controls are located on the fan panel
assemblies between the elements and fan blades and marked
“reset”. The red reset buttons can be seen through the front grille
when the heater is installed. To reset, allow the heater to cool, then
push the red buttons that are visible through the hole in the fan
panels. The heater should immediately return to normal operation.
Determine why manual reset tripped! (See Caution note)
Maintenance
Once each year the heater should be cleaned to remove dust
and other foreign material which has collected during the heating
season. This is a simple operation when performed as follows:
1. Turn off the electric power at main line switch (or remove all
fuses) to disconnect electric power from the heater. THIS IS
IMPORTANT.
2. Remove the grille and turn the disconnect switch to the OFF
position.
3. With a vacuum cleaner nozzle or dust cloth, remove dust
and other foreign material.
4. After cleaning, turn disconnect switch to ON position and
reinstall the grille.
5. Turn on the main line switch (or replace fuses) to restore
power to the heater. The heater is now ready for another
season of operation.
OPERATION OF THE MANUAL RESET SAFETY THERMAL LIMIT CON-
TROL IS AN INDICATION THAT THE HEATER HAS BEEN SUBJECTED
TO SOME ABNORMAL CONDITION. IT IS RECOMMENDED THAT THE
HEATER BE CHECKED BY A REPUTABLE ELECTRICIAN OR REPAIR
SERVICE TO ENSURE THE HEATER HAS NOT BEEN DAMAGED.
DO NOT USE WATER OR DAMP CLOTH FOR CLEANING AND DO
NOT DISTURB THE HEATING ELEMENT.
LIMITED WARRANTY
All products manufactured by Marley Engineered Products are warranted against defects in workmanship and materials for one year from date of installation, except heat-
ing elements which are warranted against defects in workmanship and materials for five years from date of installation. This warranty does not apply to damage from acci-
dent, misuse, or alteration; nor where the connected voltage is more than 5% above the nameplate voltage; nor to equipment improperly installed or wired or maintained
in violation of the product’s installation instructions. All claims for warranty work must be accompanied by proof of the date of installation.
The customer shall be responsible for all costs incurred in the removal or reinstallation of products, including labor costs, and shipping costs incurred to return products
to Marley Engineered Products Service Center. Within the limitations of this warranty, inoperative units should be returned to the nearest Marley authorized service cen-
ter or the Marley Engineered Products Center, and we will repair or replace, at our option, at no charge to you with return freight paid by Marley. It is agreed that such
repair or replacement is the exclusive remedy available from Marley Engineered Products.
THE ABOVE WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED. AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE AFORESAID EXPRESSED WARRANTIES ARE HEREBY DISCLAIMED AND EXCLUDED FROM
THIS AGREEMENT. MARLEY ENGINEERED PRODUCTS SHALL NOT BE LIABLE FOR CONSEQUENTIAL DAMAGES ARISING WITH RESPECT TO THE PROD-
UCT, WHETHER BASED UPON NEGLIGENCE, TORT, STRICT LIABILITY, OR CONTRACT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights which vary from state to state.
For the address of your nearest authorized service center, contact Marley Engineered Products in Bennettsville, SC, at 1-800-642-4328. Merchandise returned to the fac-
tory must be accompanied by a return authorization and service identification tag, both available from Marley Engineered Products. When requesting return authoriza-
tion, include all catalog numbers shown on the products.
MODEL NO.
Q6004
DATE CODE: 0996
FAN FORCED WALL HEATER
APPAREIL DE CHAUFFAGE MURAL À AIR PULSÉ
240 6000 1
VOLTS AC 60HZ WATTS PHASE
USE ONLY WITH TWO FAN PANELS
MODEL FP3004
A N’UTILISER QU’AVEC LE TABLEAU À
DEUX VENTILATEURS MODÈLE FP3004
DO NOT OPERATE WITHOUT FRONT COVER IN PLACE
NE PAS UTILISER SI LE COUVERCLE AVANT
N’EST PAS EN PLACE
MARLEY ENGINEERED PRODUCTS
BENNETTSVILLE, SC 29512
4104-2171-001
774G LISTED
ROOM HEATER
IMPORTANT
CAUTION
CAUTION
HOW TO ORDER REPAIR PARTS
In order to obtain any needed repair or replacement parts,
warranty service or technical information, please contact Marley
Engineered Products Service Center toll-free by calling
1-800-642-HEAT.
When ordering repair parts, always give the information listed as
follows:
8/97
Part No. 5200-2288-001
ECR 33603
NAMEPLATE
!
!
!
MORE THAN ONE DISCONNECT MAY BE NECESSARY IF RELAY
ACCESSORY IS USED.
1. The Part Number
2. The Model Number
3. The Part Description
4. Date of Manufacture
4
470 Beauty Spot Rd. East
Bennettsville, SC 29512 USA