Appendix iii: remote wiring – Tweco Ultima 150 User Manual
Page 43
Manual 0-2472
37
APPENDICES
APPENDIX III: REMOTE WIRING
Notes:
1. Welding Arc/ON disabled without closing TB1-3 to TB1-4. This
must be done by direct interface to TB1-3 & TB1-4 or via remote
connection J20 Pin 3 to 4.
2. To disable the pilot arc when coolant conductivity level is high,
connect pin 12 to pin 24 and pin 13 to pin 23.
3. Weld Arc On Detect (for use with Synerweld 2100) is enabled
with the following wiring connections*:
• TB1-6 to J20 pin 11
• TB1-7 to J20 pin 12
(If not using J20, wire directly from input/output interface sig-
nals to TB1.)
* Ultima units manufactured after Nov. 1997 are factory-wired;
all other units must be wired by user.
4. Wiring Connections for the 3A Torch with Auto Wire Feed are
through J20 to Quick Disconnect.
TB1
Quick
Disconnect
J20
A-00830
Rear Panel View
A-00831
OUTPUTS INPUTS
11
12
2
5
6
Quick
Disconnect
1
2
6
- PAK 200i (160 pages)
- 211i Fabricator (96 pages)
- 15C Drag-Gun LT (32 pages)
- AirCut 15C (36 pages)
- TD-750 Cutting Systems (32 pages)
- TD-750 Cutting Systems (32 pages)
- 6000 Cutting System (36 pages)
- 100 Auto-Cut (104 pages)
- 100 Auto-Cut (148 pages)
- Auto-Cut 100 Torch Operation (20 pages)
- 200 Auto-Cut (136 pages)
- 300 Auto-Cut (164 pages)
- C-20A CUTSKILL (32 pages)
- C-35A CUTSKILL (36 pages)
- C-70A CUTSKILL (36 pages)
- 15XC CE Merlin PAK (134 pages)
- 6000 CE Merlin (78 pages)
- Merlin 6000 Plasma Cutting CE Slave Power Supply (48 pages)
- 6000GST Merlin Plasma Cutting CE Slave Power Supply (78 pages)
- 150XL CE PAK Master Without Latch Circuit (54 pages)
- CutMaster 101 (62 pages)
- CutMaster 101 with SL100SV (172 pages)
- CutMaster 10mm (66 pages)
- CutMaster 10mm-12mm (44 pages)
- CutMaster 12mm-20mm-25mm (80 pages)
- CutMaster 12mm (76 pages)
- 151 CutMaster (60 pages)
- 151 with SL100SV (172 pages)
- 152 CutMaster (84 pages)
- 15mm Cutmaster (44 pages)
- 20mm Cutmaster (80 pages)
- 25mm Cutmaster (80 pages)
- CutMaster 35mm 40mm (80 pages)
- CutMaster 35mm (84 pages)
- 38 CutMaster (54 pages)
- 38 CutMaster (51 pages)
- 39 CutMaster (68 pages)
- 42 CutMaster Operating Manual (35 pages)
- 42 CutMaster Service Manual (78 pages)
- 50 CutMaster (44 pages)
- 51 CutMaster (60 pages)
- 51 with SL100SV CutMaster (172 pages)
- 102 Cutmaster (80 pages)
- 82 PlazMaster (80 pages)
- 81 CutMaster (63 pages)