Tweco 6000GST Cutting Systems - Manual (Page 57)

Man
ual 0-2690
A-11
APPENDIX
NOTE
Piercing materials 3/4 inch (19.1 mm) and over may shorten torch consumable parts life.
Metric Measurements
Air Plasma Cutting Data Chart
Maximizer 300 Torch
Mild Steel - Underwater (Water Table)
Air Plasma / Air Secondary
Electrode
Gas
Distributor
Tip End Cap Amperage
Output
Volts
Speed Standoff
Plasma
Pressure
Plasma
Flowball
Secondary
Pressure
Pierce
Delay
Pierce
Height
Cat. No. Cat. No. Cat. No. Cat. No. amps vdc m / min mm bar bar seconds mm
20-1018 20-0008 20-1031 20-1028 100 145 10.16 4.78 5.52 90 5.17 0.00 5.08
20-1018 20-0008 20-1031 20-1028 100 145 5.72 4.78 5.52 90 5.17 0.20 5.08
20-1018 20-0008 20-1031 20-1028 100 150 3.43 4.78 5.52 90 5.17 0.20 5.08
20-1018 20-0008 20-1031 20-1028 100 155 2.67 4.78 5.52 90 5.17 0.20 5.08
20-1018 20-0008 20-1031 20-1028 100 160 1.91 6.35 5.52 90 5.17 0.30 7.62
20-1018 20-0008 20-1032 20-1028 150 140 4.06 6.35 5.52 90 5.17 0.00 6.35
20-1018 20-0008 20-1032 20-1028 150 150 2.29 6.35 5.52 90 5.17 0.20 9.53
20-1018 20-0008 20-1032 20-1028 150 160 1.65 6.35 5.52 90 5.17 0.50 9.53
20-1018 20-0008 20-1032 20-1028 150 165 1.14 6.35 5.52 90 5.17 0.50 12.70
20-1018 20-0008 20-1032 20-1028 150 170 0.76 6.35 5.52 90 5.17 0.75 12.70
20-1018 20-0008 20-1033 20-1028 225 150 2.54 6.35 5.52 90 5.17 0.00 12.70
20-1018 20-0008 20-1033 20-1028 225 155 1.91 6.35 5.52 90 5.17 0.25 12.70
20-1018 20-0008 20-1033 20-1028 225 160 1.27 6.35 5.52 90 5.17 0.25 12.70
20-1018 20-0008 20-1033 20-1028 225 165 0.64 6.35 5.52 90 5.17 0.50 12.70
20-1021 20-1009 20-1034 20-1028 300 150 1.78 9.53 5.52 120 5.17 0.25 12.70
20-1021 20-1009 20-1034 20-1028 300 155 1.02 9.53 5.52 120 5.17 0.50 12.70
20-1021 20-1009 20-1034 20-1028 300 160 0.64 9.53 5.52 120 5.17 NR NR
20-1021 20-1009 20-1034 20-1028 300 165 0.51 9.53 5.52 120 5.17 NR NR
31.8
25.4
38.1
6.4
19.1
9.5
12.7
15.9
12.7
15.9
19.1
25.4
4.8
6.4
9.5
19.1
Material
Thickness
mm
1.6
3.2