Document Outline

• 0-5141-CCR
• SECTION 1:GENERAL INFORMATION
  • 1.01 Notes, Cautions and Warnings
    • 1.02 Important Safety Precautions
      • 1.03 Publications
      • 1.04 Note, Attention et Avertissement
      • 1.05 Precautions De Securite Importantes
      • 1.06 Documents De Reference
      • 1.07 Statement of Warranty
  • SECTION 2 SYSTEM: INTRODUCTION
    • 2.01 Working Principle
      • 2.02 Power Supply Specifications
      • 2.03 Input Wiring Specifications
      • 2.04 Power Supply Features
  • SECTION 2 TORCH:INTRODUCTION
    • 2T.01 Scope of Manual
      • 2T.02 Specifications
      • 2T.03 Introduction to Plasma
  • SECTION 3: INSTALLATION
    • 3.01 Unpacking
      • 3.02 Lifting Options
      • 3.03 Primary Input Power Connections
      • 3.04 Air Supply Connections
  • SECTION 4 SYSTEM: OPERATION
    • 4.01 Control Panel
      • 4.02 Preparations For Operating
      • 4.03 Sequence of Operation
      • 4.04 Cut Quality
      • 4.05 General Cutting Information
  • SECTION 5 SYSTEM: SERVICE
    • 5.01 General Maintenance
      • 5.02 Basic Troubleshooting Guide
  • SECTION 5 TORCH:SERVICE
    • 5T.01 General Maintenance
      • 5T.02 Inspection and Replacement of Consumable Torch Parts
  • SECTION 6: PARTS LISTS
    • 6.01 Introduction
      • 6.02 Power Supply Replacement Parts
      • 6.03 SL40 Torch Replacement Parts
      • 6.04 Optional Accessories
  • APPENDIX 1: CUTMASTER 42 CIRCUIT DIAGRAM
  • APPENDIX 2: SL40 TORCH PIN-OUT DIAGRAM
• SECTION 1: GENERAL INFORMATION
  • 1.01 Notes, Cautions and Warnings
  • 1.02 Important Safety Precautions
  • 1.03 Publications
  • 1.04 Note, Attention et Avertissement
  • 1.05 Precautions De Securite Importantes
  • 1.06 Documents De Reference
  • 1.08 Statement of Warranty
• SECTION 2 SYSTEM: INTRODUCTION
  • 2.01 Working Principle
  • 2.02 Power Supply Specifications
  • 2.03 Input Wiring Specifications
  • 2.04 Power Supply Features
• SECTION 2TORCH: INTRODUCTION
  • 2T.01 Scope of Manual
  • 2T.02 Specifications
  • 2T.03 Introduction to Plasma
• SECTION 3: INSTALLATION
  • 3.01 Unpacking
  • 3.02 Lifting Options
  • 3.03 Primary Input Power Connections
• SECTION 4 SYSTEM: OPERATION
  • 4.01 Control Panel
  • 4.02 Preparations For Operating
  • 4.03 Sequence of Operation
  • 4.04 Cut Quality
• SECTION 5 SYSTEM: SERVICE
  • 5.01 General Maintenance
  • 5.02 Basic Troubleshooting Guide
• SECTION 5 TORCH: SERVICE
  • 5T.01 General Maintenance
  • 5T.02 Inspection and Replacement of Consumable Torch Parts
• SECTION 6: PARTS LISTS
  • 6.01 Introduction
  • 6.02 Power Supply Replacement Parts
  • 6.03 SL40 Torch Replacement Parts
  • 6.04 Optional Accessories
• APPENDIX 1: CUTMASTER 42 CIRCUIT DIAGRAM
• APPENDIX 2: SL40 TORCH PIN-OUT DIAGRAM
• 0-5141-Rear