Reloop JOCKEY 3 REMIX - Manual (Page 33)

33
ENGLISH
7.3 Troubleshooting
If any problem should arise while using Reloop Jockey 3 the following chart is the first drop-in center:
8. Technical Specifications
The following specifications are not verified by Global Distribution GmbH in terms of plausibility and accuracy:
8.1 General Section
Power Source:
USB 5V 500mA / DC: 6V, 2A
Dimensions: 420 x 61.55 x 315 mm
Weight: 5.1 kg
8.2 USB Slave Player Section (Signal Format MP3, 128 kbps, sony Sound Forge 8.0)
8.2.1 Output Level (Sony Sound Audio device Type: Jockey 3 ReMIx)
Master Out:
-11 dBV +/-2 dB (TCD782 TRK16)
Phones Out: -10 dBV +/-2 dB (TCD782 TRK16)
8.2.2 Frequency Response (Sony Sound Audio device Type: Windows Classic Wave driver)
Master Out:
17-16 kHz +/-1.5 dB (TCD782, TRK1, 4, 16)
8.2.3 THd+n (Sony Sound Audio device Type: Windows Classic Wave driver)
Master Out:
< 0.01% (TCD782 TRK2, Master VR Out: 0dB) w/20 kHz LPF, A-weighted
Master Out: < 0.01% (96K-TCD782 TRK2, Master VR Out: 0 dB) w/ 20 kHz LPF, A-weighted
8.2.4 S/N Ratio (Sony Sound Audio Device Type: Windows Classic Wave driver)
Master Out:
> 95 dB (TCD782 TRK2, 8; Master VR Out: Max) w/20 kHz LPF, A-weighted
8.2.5 LR Separation (Sony Sound Audio device Type: Windows Classic Wave driver)
Master Out:
> 85 dB (TCD782 TRT9, 11) w/ 20 kHz LPF, A-weighted
8.3 USB Slave Recording & Playback (Line 1 kHz, 0 dBv, Mic 1 kHz -36 dB Input, 44.1K Sample Rate 24 bit)
8.3.1 Output +3dBV (1.41V) +/- 1.5 dB
THD+N:
< 0.02% (w/20 kHz LPF, A-weighted)
THD+N: < 0.02% (w/20 kHz LPF, A-weighted 96K Sample Rate 24 bit)
8.4 S/N Ratio +3 dBV (1.41V) +/- 1.5 dB
Line:
> 82 dB (w/20 kHz LPF, A-weighted)
Mic: > 70 dB (w/20 kHz LPF, A-weighted)
Crosstalk: > 75 dB zwischen L und R Kanal (w/20 kHz LPF, A-weighted)
Reloop Distribution
Global Distribution GmbH, Schuckertstrasse 28, 48153 Münster / Germany
Fax: +49.251.6099368
Subject to alterations.
Illustrations similar original product.
Misprints excepted.
SYMPTOMe POSSIBLe CAUSeS CORReCTIve MeASUReS
The device does not receive any power when
turning it on via the ON/OFF Button -B56-. USB cord or mains adapter are not connected
correctly. Check whether the USB cord is connected correctly to a free USB port
of your computer and Jockey 3 Remix's USB port -B57-. Please also
check whether the mains adapter is connected correctly to the mains
connection -B55-.
The Controller's LEDs are only weakly lit and the
device does not react. The power supply is not sufficient. Connect your computer to a secured power line. Also it is necessary to
connect the included mains adapter to the corresponding jack -B55-.
Not all outputs of the integrated audio interface
can be selected in the DJ software. The ASIO driver is not installed correctly. Please install the ASIO driver again. Also please read the paragraph
“ASIO Driver Installation“ in the chapter “Computer Configuration“.
The audio interface's sound is distorted. The ASIO driver is not used.
The performance settings of your computer do
not correspond to the computer's capacity. Please make sure that the ASIO driver is installed and is also being used.
Please refer to the paragraph “ASIO Driver Installation“ in the chapter
“Computer Configuration“.
It is also possible that in the ASIO driver's settings the available compu-
ter capacity has to be re-configured. Open the settings in Traktor, select
the category “Audio Setup“ and click on the “Settings“ button next to
the sound card selection window. Then select “System Performance“ >
“Normal“. If the problems persist you can also select “Relaxed“ in the
same menu.
The DJ software does not show any reaction
to the usage of any of the contoller's control
elements. Traktor LE 2 is not configured correctly.
Traktor Pro 2 is not installed correctly. If you use the included Traktor LE 2 version, start the Setup Wizard
again. Refer to the paragraph “Traktor LE 2 Setup“ in the chapter
“Computer Configuration“.
When using Traktor Pro 2 the mapping has to be loaded again. To do so
follow the instructions in the paragraph “Traktor Pro 2 Configuration“ in
the chapter “Computer Configuration“.
The decks do not react to the control elements
of the controller. The Deck Select Switches are in the IN1/IN2
position. Make sure that the Deck Select Switches are switched to the Traktor
decks.
In analog mode the inputs are not played via the
master output. The two Input Switches are not in the MIX
position. Put both Input Switches to MIX position.
The MIDI signals are not being routed on Mac
OSX. On Mac OSX the MIDI ports are blocked. Download the free tool “MIDI Monitor” and start it once.
Only the mixer section in Traktor works. The MIDI channels are not adjusted correctly. Please read chapter 5.1.1 and adjust the Jockey 3 Remix to MIDI preset 1.
There is a problem that is not listed here. Various causes. Visit the website www.reloop.com/forum in order to get support regar-
ding your Reloop products.