Amplifier programming, Timing logic programming, All cd series modules) – Banner MAXI-AMP Series User Manual
Page 5: Cd5 models), Switches #2 and #3, Switch #4, Switch #1

Amplifier Programming
(all CD Series modules)
The diagram at the left shows the location of switches 1-4,
and the table summarizes the settings required for each
response condition.
NOTE: An adhesive-backed mylar label is supplied. It may
be marked to indicate switch programming and then ap-
plied to the MAXI-AMP housing as a switch cover.
Factory settings are
shown at left. The
"underlined" settings in
table below are factory
settings.
OFF
ON
OFF
AMPLIFIER
PROGRAMMING
#1
#2
#3
#4
SWITCH
SWITCH
SWITCH
SWITCH
ON
O
F
F
1
2
3
4
Modulation freq. "A"
1.5 millisecond response
15 millisecond response
Light operate
Dark operate
ON
ON
OFF
Modulation freq. "B"
OFF
ON
ON
OFF
ON
ON
ON
ON
OFF
ON
OFF
ON
PROGRAMMING
TIMING LOGIC
#1
#2
#3
#4
#5
#6
#7
#8
#9
#10
10
ON
O
F
1
2
4
3
F
5
6
7
8
9
SWITCH
SWITCH
SWITCH
SWITCH
ON
ON
ON
ON
OFF
OFF
OFF
SWITCH
SWITCH
SWITCH
SWITCH
SWITCH
SWITCH
On/Off
On Delay
Off Delay
On and Off Delay
One-shot
Delayed One-shot
Limit
Repeat Cycle
AC Latch
DC Latch
Delay and Latch
Limit and Latch
ON
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
ON
ON
OFF
ON
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
OFF
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
ON
ON
N/C Output
N/O Output
.15 Sec. Max. Time
1.5 Sec. Max. Time
15 Sec. Max. Time
OFF
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
ON
5
A group of ten switches, located on the side of the module opposite the amplifier program
switches, is used to select the timing logic for the CD5 models.
Switches #1 through #7 are used to select the logic function. Switch #8 programs the output for
either NORMALLY OPEN or NORMALLY CLOSED operation. Switches #9 and #10
program the time range(s). There are three ranges: 10 to 150 milliseconds, 0.1 to 1.5 seconds,
and 1 to 15 seconds. The programmed range will be the same for both functions of a dual timing
mode (ON & OFF DELAY, DELAYED ONE-SHOT, and REPEAT CYCLE). However,
DELAY and HOLD times are independently adjustable within the selected range.
The diagram shows switch locations, and the
table summarizes the program switch posi-
tions.
tion frequencies. This makes it possible to use the two sensor pairs
in close proximity without optical crosstalk. Both amplifiers must
be set for the same response time (either 1.5 or 15 milliseconds) to
ensure freedom from crosstalk.
Switches #2 and #3
are used to program the amplifier response
time. The 15 millisecond setting allows SP12 Series sensors to
operate at their maximum excess gain.
Switch #4
is used to select LIGHT OPERATE or DARK OPER-
ATE. In the LIGHT OPERATE mode, the output will energize (in
ON/OFF or LATCH operation) or the timing function will initiate (in
DELAY, ONE-SHOT, or LIMIT operation) when the receiver
"sees" sufficient light (excess gain greater than 1X). In DARK
OPERATE, the output will energize or timing will begin when the
receiver is sufficiently dark (excess gain less than 1X).
Amplifier response conditions may be programmed via the group of four
switches located on one of the narrow sides of the MAXI-AMP™
module.
Switch #1
selects the modulation frequency of the amplifier and the
emitter light source. When two pairs of SP12 Series sensors are being
used in close proximity to each other, the modulation frequency switch
of their respective CD Series modules should be set to different modula-
Settings illustrated below are factory settings. Factory settings are "underlined" in the table.
Timing Logic Programming
(CD5 models)