Timing logic programming, Hookup of multiple self-contained sensors, Cl5 models) – Banner MAXI-AMP Series User Manual
Page 21
LIGHT OPERATE
DARK OPERATE
DARK OPERATE
If any receiver "sees"
light
When all receivers
"see" dark
OUTPUT OCCURS
(AFTER DELAY, IF
ANY)
If any receiver "sees"
dark
When all receivers
"see" light
NO
NO
YES
(NOTE: see page 6 for
description of logic functions)
YES
LIGHT OPERATE
INVERTING JUMPER
Installed Between Module
Terminals #10 and #11
SENSOR PROGRAM:
Light or Dark Operate
LOGIC DESCRIPTION
The diagram shows switch locations,
and the table summarizes the program
switch positions.
Hookup of Multiple Self-contained Sensors
Any number of self-contained dc sensors may be wired to-
gether in parallel to a single CL Series MAXI-AMP module to
create almost any multiple-sensor logic configuration. Power
for the sensors may be obtained from MAXI-AMP 400mA
power supply CP12 (shown below) or from 1-amp model
PS120-15. The table at the right describes how the four most
frequently used multiple-sensor logic configurations may be
created.
MINI-BEAM SM312 Series and VALU-BEAM SM912 Se-
ries sensors have a switch on the back of their housings which
is used to program the sensors for LIGHT or DARK operate.
MAXI-BEAM sensors are set for LIGHT or DARK operate
using the programming ring. MULTI-BEAM sensors are
programmed for LIGHT or DARK operate with the logic
module jumper wire. OMNI-BEAMs are programmed by a
switch in the sensor block.
For ON/OFF sensor operation, light operate is equated to
normally open output, and dark operate is defined as
normally closed. EZ-BEAM sensors have both a normally
open and a normally closed output. Selection of either output
determines the LIGHT/DARK operate mode. ECONO-BEAM
sensors are not programmable and must be ordered for LIGHT
OPERATE (standard models) or DARK OPERATE (model
suffix "NC").
The addition of a jumper wire between MAXI-AMP terminals
#10 and #11 changes the input response from a low-going to
a high-going signal. This feature, combined with the selection
of LIGHT or DARK operate at the sensor, allows "AND" logic
with parallel sensor connections.
Timing Logic Programming
(CL5 models)
Settings illustrated below are factory settings. Factory settings are "underlined" in the table.
A group of ten switches located on one side of the module is used to select the timing logic for
CL5 models.
Switches #1 through #7 are used to select the logic function. Switch #8 programs the output
for either NORMALLY OPEN or NORMALLY CLOSED operation. Switches #9 and #10
program the time range(s). There are three ranges: 10 to 150 milliseconds, 0.1 to 1.5 seconds,
and 1 to 15 seconds. The programmed range will be the same for both functions of a dual timing
mode (ON & OFF DELAY, DELAYED ONE-SHOT, and REPEAT CYCLE). However,
DELAY and HOLD times are independently adjustable within the selected range.
21
LIGHT "OR"
DARK "AND"
DARK "OR"
LIGHT "AND"
105-130V ac
Brown
+V dc
Brown
+V dc
Blue
(#1)
White
+V dc
Brown
105-130V AC
Blue
(#1)
SM31R/RL
White
SM31R/RL
SM31E/EL
Blue
(#1)
Brown
+V dc
Blue
SM31R/RL
White
CL3
or
CL5
model
8
7
6
5
4
CP12
power
supply
8
7
6
5
4
9
10
11
1
2
3
SM31E/EL
Blue
(#1)
Brown
+V dc
SM31E/EL
Blue
(#1)
Brown
+V dc
9
10
11
1
2
3
ON
OFF
ON
ON
ON
ON
OFF
ON
OFF
ON
PROGRAMMING
TIMING LOGIC
#1
#2
#3
#4
#5
#6
#7
#8
#9
#10
10
ON
O
F
F
1
2
3
4
5
6
7
8
9
SWITCH
SWITCH
SWITCH
SWITCH
ON
ON
ON
ON
OFF
OFF
OFF
SWITCH
SWITCH
SWITCH
SWITCH
SWITCH
SWITCH
On/Off
On Delay
Off Delay
On and Off Delay
One-shot
Delayed One-shot
Limit
Repeat Cycle
AC Latch
DC Latch
Delay and Latch
Limit and Latch
ON
ON
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ON
ON
ON
OFF
OFF
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
ON
ON
OFF
ON
ON
ON
ON
ON
ON
OFF
ON
ON
ON
ON
ON
OFF
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
ON
ON
N/C Output
N/O Output
.15 Sec. Max. Time
1.5 Sec. Max. Time
15 Sec. Max. Time
OFF
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
ON
OFF
ON