DJI Wookong-H - Manual (Page 23)

©2012 DJI Innovations. All Rights Reserved. 23 |
C4
Autopilot Test Fight
 WKH Test Flight ( Lite WKH Lite user should skip this section to WKH Lite Test Flight section on next page )
When system is powered on, you must not move your helicopter or sticks on transmitter until the system initialization is
finished (about 5 second).
Please read this section before you switched to
Atti. Mode and GPS Atti. Mode
1 Make sure the GPS signal is good, without red LED
blinking.
2 Please avoid using WKH system in the following areas,
where will GPS signal is most likely blocked:
 Urban area with crowded buildings
 Tunnels
 Under bridges
3 Make sure the attitude of helicopter is in good condition,
without white LED blinking.
4 Other system failures and errors will also be displayed
by LED indicator (see Appendix for details) or in
assistant software.
5 If WKH has already acquired the GPS signal, you
cannot unplug GPS module directly without reboot and
fly in GPS Atti Mode.
STEP1: Check all connections and wirings, and make sure they are
in good condition;
STEP2: Make sure your batteries are fully charged for your
transmitter, WKH and all the devices on your helicopter;
STEP3: Turn on the transmitter first;
STEP4: Power on WKH and all the rest of electric device on
helicopter, except brushless motor controller;
STEP5: Check the LED indicator. If red LED sparks quickly, the
system start-up has failed. You will need to place your
helicopter horizontally and power on again. See Appendix
for details about LED indicator;
STEP6: You may find red LED blinking, indicating that WKH is
getting GPS satellite signal, please wait until red LED is off,
meaning WKH have found more than 7 GPS satellites, and
that it can work in its best condition. See Appendix for
details about LED indicator;
STEP7: Slide the control mode switch on your transmitter to make
sure it is working properly. Check it with LED indicator to
specify the current working mode for WKH. See Appendix
for details about LED indicator;
STEP8: Switch the system to GPS ATTi. Mode, if the swashplate is
not horizontal, please go back to 3 rd step, and power cycle
the system;
STEP9: Switch the system to Manual Mode, move all the sticks on
your transmitter to check whether the helicopter is correctly
responding to your commands;
STEP10: Start the engine or power on the brushless motor controller;
STEP11: Take-off and fly your helicopter in Manual Mode;
STEP12: Hover your helicopter, and switch to GPS ATTi. Mode.
 Semi-Auto take-off
Please setup B7 Engine Governor and all center positions
correctly before you use this function. On STEP11, the
system can perform Semi-Auto take-off feature rather than
manual take-off. Please follow the operation procedures
strictly:
1 Put the throttle stick on the lowest position;
2 Switch to GPS Atti. or Atti. Mode and wait until the
speed of main rotor is stable ;
3 Requiring only pushing the throttle (collective pitch) stick
gently to take-off the helicopter, autopilot system will be
in charge of the cyclic pitch/roll stabilization.
 Semi-Auto Landing
In GPS Atti. or Atti. Mode, with throttle (collective pitch) stick
operation only, descend the helicopter and hold throttle stick
on lowest position until the engine or electric motor is cutoff
automatically. This throttle idle or shut-down in Auto mode
when collective is lowest stick position only applies having
this option.
1 With this option, MC will perform in GPS Atti.
Or Atti. Mode for both takeoff and landing.
2 Make sure use this function only when the GPS signal is
sufficient and at open area!
3 When you are using semi auto take off, switch into
autopilot modes and move throttle stick, main rotor will
start!
Do NOT move any stick when switching!
 WKH Lite Test Flight