Rockwell Automation 20B PowerFlex 700 Power Jumpers User Manual
Page 7
PowerFlex 700 Power Jumpers
7
Publication 20B-IN021B-EN-P
Frame
Vo
lt
ag
e
Code
Cur
rent
Rating
Factory Default Jumper Settings
Power Source Type
MOV/Input Filter
Caps
(1) (2)
DC Bus Common
Mode Caps
5
NEMA/UL Type 12 Drives
C
D
P
R
All
Two green/yellow
wires connected
to chassis ground
Green/yellow wire
is connected to
ground
Solid Ground
1. CM Cap jumper wire should be
connected to ground with a metal screw.
Verify.
• Newer Drives - If necessary, remove
the nylon screw/spacer and insert a
metal M5 x 8 screw. Torque to 3.2
N•m (28 lb•in).
• Older Drives - Remove the
I/O Cassette (see User Manual for
details). The green/yellow CM Cap
jumper wire is located on the back of
chassis and should be connected to
ground with a metal screw. If
necessary, remove the insulation
from the wire terminal and connect
to chassis with a metal M5 x 10
screw. Torque screw to 3.2 N•m (28
lb•in).
2. MOV/Input Filter Cap jumper wires
should be connected to ground with a
metal screw. Verify. If necessary,
remove the nylon screw/spacer and
insert a metal M5 x 12 screw.
Non-Solid Ground
1. CM Cap jumper wire should be
insulated from ground. Verify.
• Newer Drives - If necessary, remove
the metal screw and insert a M5 x 15
nylon screw/spacer.
• Older Drives - Remove the
I/O Cassette (see User Manual for
details). If necessary, insulate/
secure jumper wire to guard against
unintentional contact with chassis or
components.
2. MOV/Input Filter Cap jumper wires
should be insulated from ground with a
nylon screw/spacer. Verify. If necessary,
remove the metal screw and insert a M5
x 20 nylon screw/spacer.
Frame 5 continued on next page
(1)
AC input drives only. MOV’s and input filter caps do not exist on DC input drives.
(2)
When removing MOV’s, the input filter capacitor must also be removed.
USE 75 C CU WIRE ONLY
WIRE RANGE: 4-3/0 AWG (18-70 MM2)
TORQUE: 133 IN-LB (15 N-M)
STRIP LENGTH: 1.02 IN (26 MM)
POWER & DC TERMINAL RATINGS
WIRE RANGE: 14-1/0 AWG (2.5-50 MM2)
TORQUE: 32 IN-LB (3.6 N-M)
STRIP LENGTH: 0.67 IN (17 MM)
BRAKE TERMINAL RATINGS
WIRE RANGE: 6-1/0 AWG (18-35 MM2)
TORQUE: 44 IN-LB (5 N-M)
STRIP LENGTH: 0.83 IN (21 MM)
GROUND TERMINAL RATINGS (PE)
OUTPUT
INPUT AC
300 VDC EXT PWR SPLY TERM (PS+, PS-)
WIRE RANGE: 22-10 AWG (0.5-4 MM2)
TORQUE: 5.3 IN-LB (0.6 N-M)
STRIP LENGTH: 0.35 IN (9 MM)
DANGER
DANGER
RISK OF ELECTRIC
SHOCK AND DEATH
FIELD INSTALLED OPTIONS
6 MM HEX KEY
6 MM HEX KEY
SHLD
SHLD
MOV
MOV / Input Filter Cap
CM Cap -
Older Drives
CM Cap - Newer Drives