Adding oil, Adding oil 73 – MTS Criterion 60 - Manual User Manual
Page 73
Adding Oil
MTS Criterion™ Series 60 Product Manual
Installation
73
Adding Oil
Make sure the type of the hydraulic oil is correct and high quality. The hydraulic
oil ( hydraulic operating fluid) is mainly used for hydraulic power unit work.
Check the level of the oil indicator carefully while you are adding oil to the
reservior until it reaches the upper limit.
Customer should follow internal safety policies for safe disposal of parts of the
machine. Refer to MSDS for oils and greases that are used on the machine.
When working with hydraulic components, hydraulic fluid can spill and
collect on floors and work platforms.
Floors and work platforms with spilled hydraulic fluid are very slippery.
Injury or death can result from personnel falling on slippery surfaces.
Do not allow personnel to stand on or walk through hydraulic fluid. place warning
signs around the spill area to alert personnel of the hazard. Clean and dry the spill
promptly.
Only add oil through the air strainer.
Clean up oil spills immediately.
CAUTION
- Series 111 Accumulator (40 pages)
- Series 249G2 Swivels (34 pages)
- Series 201 Actuators (40 pages)
- Series 215 Rotary Actuator (68 pages)
- Series 242 Actuators (40 pages)
- Series 244 Actuators (68 pages)
- Series 247 Actuators (40 pages)
- Series 248 Actuators (46 pages)
- 709 Alignment System (158 pages)
- Series 609 Alignment Fixture (70 pages)
- 494 Controller Hardware FT 40 (344 pages)
- ReNew Technical Reference (50 pages)
- DCPD Measurement System (46 pages)
- Bionix EnviroBath (40 pages)
- FGW900 High-temperature Furnace (38 pages)
- Model 409.83 Temperature Controller (40 pages)
- Series 651 Environmental Chambers (30 pages)
- Series 653 High-Temperature Furnaces (38 pages)
- Series 658 Environmental Chamber (24 pages)
- Series FEC Environmental Chamber (48 pages)
- Model 685.53 Grip Control Module (24 pages)
- Series 685 Hydraulic Grip Supply (48 pages)
- Bend Fixture-10 kN (2 pages)
- Grip-Manual Bend Fixture-100 kN (2 pages)
- Grip-Manual Bollard-2 kN (2 pages)
- Grip-Manual Bollard-500 N (2 pages)
- Compression Platen-100 kN-100mm (2 pages)
- Compression Platen-100 kN-150mm (2 pages)
- Compression Platen-100 kN-200mm (2 pages)
- Compression Platen-20 kN (2 pages)
- Compression Platen-20 kN-100mm (2 pages)
- Compression Platen-20 kN-200mm (2 pages)
- Compression Platen-20 kN-SST (2 pages)
- Compression Platen-500 N FYC502A (2 pages)
- Compression Platen-500 N FYB502A (2 pages)
- Compression Platen-500 N-50mm (2 pages)
- Grip-Pneumatic Vise-Style-1 kN (2 pages)
- Pneumatic Bollard-500 N (2 pages)
- Scissor-Style-2 kN (2 pages)
- Scissor-Style-5 kN (2 pages)
- Screw-Style-5 kN (2 pages)
- Screw-Style-5 kN-SST (2 pages)
- Bend Fixture-1000 kN (2 pages)
- Bend Fixture-300 kN (2 pages)
- Bolt Grips (32 pages)