Encoder, Limits – MTS Criterion 60 - Manual User Manual
Page 29
Specifications
MTS Criterion™ Series 60 Product Manual
Introduction
29
Encoder
This is intended to connect the frame displacement sensor to the encoder on the
Insight Controller. It is DC-powered and collects the digital encoder signals
frome the displacement sensor. Pin Assignment is as follows:
Limits
This connector is intended to connect the frame limit and the logic board. It is
used to transmit the state signal of the frame limit. Pin assignment is as follows:
14
TEDS-
15
EXS-
Pin Assignment (Continued)
P
IN
S
IGNAL
Pin Assignment
P
IN
S
IGNAL
1
A+
2
A-
3
No Contact
4
GND
5
VCC
6
No contact
7
Shield
8
TEDS+
9
No Contact
10
B-
11
No Contact
12
I+
13
I-
14
TEDS-
15
B+
Pin Assignment
P
IN
S
IGNAL
1
PISTON COM
2
PISTON NO
3
XHD UP NC
4
XHD LO COM
5
XHD LO NO
See also other documents in the category MTS Hardware:
- Series 111 Accumulator (40 pages)
- Series 249G2 Swivels (34 pages)
- Series 201 Actuators (40 pages)
- Series 215 Rotary Actuator (68 pages)
- Series 242 Actuators (40 pages)
- Series 244 Actuators (68 pages)
- Series 247 Actuators (40 pages)
- Series 248 Actuators (46 pages)
- 709 Alignment System (158 pages)
- Series 609 Alignment Fixture (70 pages)
- 494 Controller Hardware FT 40 (344 pages)
- ReNew Technical Reference (50 pages)
- DCPD Measurement System (46 pages)
- Bionix EnviroBath (40 pages)
- FGW900 High-temperature Furnace (38 pages)
- Model 409.83 Temperature Controller (40 pages)
- Series 651 Environmental Chambers (30 pages)
- Series 653 High-Temperature Furnaces (38 pages)
- Series 658 Environmental Chamber (24 pages)
- Series FEC Environmental Chamber (48 pages)
- Model 685.53 Grip Control Module (24 pages)
- Series 685 Hydraulic Grip Supply (48 pages)
- Bend Fixture-10 kN (2 pages)
- Grip-Manual Bend Fixture-100 kN (2 pages)
- Grip-Manual Bollard-2 kN (2 pages)
- Grip-Manual Bollard-500 N (2 pages)
- Compression Platen-100 kN-100mm (2 pages)
- Compression Platen-100 kN-150mm (2 pages)
- Compression Platen-100 kN-200mm (2 pages)
- Compression Platen-20 kN (2 pages)
- Compression Platen-20 kN-100mm (2 pages)
- Compression Platen-20 kN-200mm (2 pages)
- Compression Platen-20 kN-SST (2 pages)
- Compression Platen-500 N FYC502A (2 pages)
- Compression Platen-500 N FYB502A (2 pages)
- Compression Platen-500 N-50mm (2 pages)
- Grip-Pneumatic Vise-Style-1 kN (2 pages)
- Pneumatic Bollard-500 N (2 pages)
- Scissor-Style-2 kN (2 pages)
- Scissor-Style-5 kN (2 pages)
- Screw-Style-5 kN (2 pages)
- Screw-Style-5 kN-SST (2 pages)
- Bend Fixture-1000 kN (2 pages)
- Bend Fixture-300 kN (2 pages)
- Bolt Grips (32 pages)