Sheet2, Detail view j (1 : 2.5), Detail view k (1 : 2.5) – ERICO CADDY ROD LOCK Beam Clamp User Manual
Page 2: Detail view l (1 : 2), Detail view m (1 : 2.5), Drawing view127, Drawing view126, Drawing view124, Drawing view128, Drawing view129
Tighten the set screw with
60 in-lb(6.8 N-m). Tighten the
jam nut.
Push rod
into beam clamp.
Tighten the set screw with
60 in-lb(6.8 N-m). Tighten
the jam nut.
top of locknut
Top of rod must be
positioned at or above
6
7
Rod adjustment
possible after
locknut tightened.
2
3
3
4
1
Method #1
* Arrows on CADDY
®
ROD LOCK Beam Clamps must always point up.
* Arrows on CADDY
®
ROD LOCK Beam Clamps must always point up.
1
As shipped
4
As shipped
Method #2
Follow installation steps 5-7
from method #1.
Hand tighten top
locknut.
5
Rotate counter clockwise
2 full turns to insert rod
2
Rotate counter clockwise
2 full turns to insert rod
TECHNICAL SUPPORT:
www.erico.com
CFS410_R
INSTRUCTION SHEET
2 OF 2
© 2009, 2010, 2011, 2012 ERICO International Corporation
CADDY
®
ROD LOCK Beam Clamp
See also other documents in the category ERICO Accessories for electrical:
- 6Z34VF14 Rod Hanging Basket Tray Clip (1 page)
- 766PM Far Side Box Support (1 page)
- 766PMD Far Side Box Support (1 page)
- CADDY MPVTI Low Voltage Mounting Clip (2 pages)
- H-Series CADDY PYRAMID Support System (3 pages)
- CADDY PYRAMID RL, PIPE RETAINERS (2 pages)
- CADDY PYRAMID Rooftop Equipment Support (4 pages)
- CADDY PYRAMID Single Post Support (1 page)
- CADDY PYRAMID TF Series, Fixed Height Tool-Free Supports (2 pages)
- CADDY ROD LOCK Anchor Screw (2 pages)
- CADDY ROD LOCK Channel Nut (2 pages)
- CADDY ROD LOCK L-Bracket (2 pages)
- CADDY ROD LOCK Strut (2 pages)
- CADDY SPEED LINK Riveted Accessories (4 pages)
- CADDY SPEED LINK SLK-Keyless Locking Device and Bulk Cable (2 pages)
- CADDY SPEED LINK SLK-Keyless Locking Devices (2 pages)
- CADDY SPEED LINK-Accessory Cables (1 page)
- CADDY SPEED LINK-SLK Cable End Accessories (4 pages)
- TSGB Series Screw Gun Bracket (2 pages)
- GLIDER Electrical Box Attachment (2 pages)
- H Series-Electrical Box Bracket (2 pages)
- ROD LOCK Plywood Pre-set Anchor (2 pages)
- ROD LOCK Strut End Bracket (2 pages)
- ROD LOCK Strut (2 pages)
- CADDY ROD LOCK Strut Nut (2 pages)
- CER4 Cable from Stud (2 pages)
- High Performance CADDY CAT HP J-Hook Assemblies (6 pages)
- KBT Wire Basket Tray Clip (1 page)
- MPCB1220 (2 pages)
- SBC Series, Beam Clamp, 3/8" and M10 (1 page)
- TSR200 Telescoping Strut Replacement Bracket (2 pages)
- TSRBS1625 Telescoping Box (3 pages)
- Universal Pedestal Clamp (2 pages)
- Branch Line Restraint Device (2 pages)
- Branch Line Restraint Strucural Attachment Fitting for Steel 12 gauge (2 pages)
- Branch Line Restraint, Structural Attachment Fitting for Concrete or Wood (2 pages)
- Branch Line Restraint, Structural Attachment Fitting with 3/8"-16 male thread" (2 pages)
- 510 CADDY EZ RISER (2 pages)
- 429 CADDY MACROFIX PLUS NI (1 page)
- Seismic Hanger Clamps (3 pages)
- CADDY PYRAMID Equipment Supports (3 pages)
- CADDY ROD LOCK Bottom-Mount Duct Bracket (2 pages)
- Bottom-Mount Duct Bracket, Narrow (2 pages)
- Top-Mount Duct Bracket (2 pages)