Installation instructions, Ammco drum & disc brake lathes • 17 – AMMCO 4000E Drum and Disc Brake lathe User Manual
Page 19
AMMCO Drum & Disc Brake Lathes • 17
Installation Instructions
Receiving
The shipment should be thoroughly inspected as soon
as it is received. The signed bill of lading is acknowl-
edgement by the carrier of receipt in good condition of
shipment covered by our invoice.
If any of the goods called for on this bill of lading are
shorted or damaged, do not accept them until the car-
rier makes a notation on the freight bill of the shorted
or damaged goods. Do this for your own protection.
NOTIFY THE CARRIER AT ONCE if any hidden loss or
damage is discovered after receipt and request the car-
rier to make an inspection. If the carrier will not do so,
prepare a signed statement to the effect that you have
notified the carrier (on a specific date) and that the car-
rier has failed to comply with your request.
IT IS DIFFICULT TO COLLECT FOR LOSS OR DAM-
AGE AFTER YOU HAVE GIVEN THE CARRIER A CLEAR
RECEIPT.
File your claim with the carrier promptly. Support your
claim with copies of the bill of lading, freight bill,
invoice, and photographs, if available.
Although AMMCO’s responsibility ceases upon deliv-
ery of the shipment to the carrier, we will gladly assist
in tracing lost shipments. Our willingness to assist in
every possible manner does not make AMMCO
responsible for collection of claims or replacement of
lost or damaged materials. Shipping damage claims will
not be handled under warranty.
Electrical Requirements
The lathe must be properly grounded to protect the
operator from shock. The lathe is equipped with an
approved 3-conductor cord and a 3-prong grounding
type plug to fit the proper grounding-type receptacle.
Should an extension cord be required, use 3-conductor
cords with 3-prong grounding plug and 3-prong ground-
ing receptacle properly rated to handle this electrical
power tool only. Do not modify a cord or plug to match
a receptacle; have a qualified electrician install an
appropriate outlet to match the lathe requirements.
Repair or replace any worn or damaged power cords
immediately.
Verify that the lathe plug and grounding-type recepta-
cle match as shown in Figure 29.
Figure 29 - Power Cord Plug and Receptacle Types
Setup
A factory trained COATS
®
Service Technician must per-
form the install, setup, and initial test procedures on
your brake lathe. Do not attempt to install and setup the
unit yourself. Accurate and reliable operation of your
unit depends on proper installation. Please contact
COATS
®
directly at 1-800-688-9240 for the Certified
Service Partner nearest you.
Connect to Power
Your factory trained COATS
®
Service Technician should
do the final check to verify the power installation before
connecting the brake lathe to a power supply. Failure
due to improper power connection may void the war-
ranty.
Operating Specifications
• Overall Lathe Height . . . . . . . . . . .17.25" [438 mm]
• Lathe Shipping Weight . . . . . . . . . .410 lbs [186 kg]
• Floor Space Requirements:
Width . . . . . . . . . . . . . . . . .48" [1219.20 mm]
Deep . . . . . . . . . . . . . . . . . .34.5" [901.70 mm]
Spindle to Floor . . . . . . . .39.375" [1000 mm]
(mounted to optional bench)
• Electrical Requirements
(unless otherwise specified)
:
Standard: 115 VAC, 60 Hz, single-phase, fused
at 20 amps
Optional: 220 VAC, 60 Hz, single-phase, fused
at 15 amps
• Spindle Motor . . . . . . . . .1 HP, 60 Hz, 115/230 VAC
• Spindle Travel . . . . . . . . . . . . . . . .9.875" [251 mm]
• Spindle Speed Lever Positions:
Lower Groove . . . . . . . . . . . . . . . . . . . . . .100
Middle Groove . . . . . . . . . . . . . . . . . . . . .150
Upper Groove . . . . . . . . . . . . . . . . . . . . . .200
• Spindle Feed Speeds . . . . . . . . . . . . . . . . .Variable
• Cross Feed Speed . . . . . . . . . . . . . . . . . . .Variable
• Handwheel Graduations . . . . . . .0.002 [0.050 mm]
• Maximum Brake Rotor:
Diameter . . . . . . . . . . . . . . . . .15" [381.0 mm]
Thickness . . . . . . . . . . . . . . . .1.9" [48.26 mm]
• Brake Drum Diameter:
Minimum . . . . . . . . . . . . . . . . . . .6" [152 mm]
Maximum . . . . . . . . . . . . . . . . . .28" [711 mm]
• Maximum Drum Depth . . . . . . . .9.875" [251 mm]
• Maximum Load:
1" Arbor . . . . . . . . . . . . . . . .200 lbs [90.72 kg]
1.875" Arbor . . . . . . . . . . . .200 lbs [90.72 kg]