JLG 600SC_660SJC ANSI Service Manual User Manual
Page 116
SECTION 6 - UNDERCARRIAGE
6-12
– JLG Lift –
3120794
NOTE: Do not install the Duo-cone seal kit in the track roller
or end collars at this time.
NOTE: Replace the o-ring seals that are used on shaft (5)
with new o-ring seals.
a. Install an o-ring seal in shaft (5) at the end that
has the spring pin hole. Lubricate the o-ring seal
with clean oil.
b. Lubricate the bore in end collar (8) with clean oil.
Use a press to install shaft (5) in end collar (8).
Be sure that the spring pin hole in the shaft is
aligned with the spring pin hole in the end collar.
Install spring pin (7) in the end collar.
c. Install shaft kit (5) in track roller (6) without Duo-
cone seal kits. Install end collar (3) without the
Duo-cone seal kits. Install retaining ring (2).
d. Use tooling (B) to measure the end play of shaft
(5). The end play of the shaft must be 0.10 to
0.49 inch (0.25 to 1.25 mm). Bearings (11) con-
trol the amount of shaft end play.
e. Disassemble the track roller, but do not remove
shaft (5) from end collar (8).
- 120HX Service Manual (116 pages)
- 544D-10 Parts Manual (730 pages)
- 100SX Parts Manual (224 pages)
- 450A Operator Manual (68 pages)
- 15DVL (3121839) Parts Manual (126 pages)
- E450 Operator Manual (106 pages)
- E450 Operator Manual (116 pages)
- G5-18A Operator Manual (142 pages)
- 2505H Operator Manual (148 pages)
- 40HA ANSI Parts Manual (322 pages)
- 400RTS Service Manual (100 pages)
- 660SJ Parts Manual (382 pages)
- 660SJ Parts Manual (352 pages)
- 660SJ Parts Manual (310 pages)
- 600S_SJ Parts Manual (299 pages)
- 600S_SJ Parts Manual (302 pages)
- 660SJ Parts Manual (404 pages)
- 660SJ Parts Manual (306 pages)
- 19AMI (3120758) Service Manual (68 pages)
- 500RTS ANSI Service Manual (80 pages)
- 400RTS ANSI Service Manual (98 pages)
- LSS Scissors (78 pages)
- 510AJ Series II Operator Manual (104 pages)
- 800S Operator Manual (158 pages)
- 800S Operator Manual (130 pages)
- 35xxPS Operator Manual (176 pages)
- 400RTS ANSI Operator Manual (48 pages)
- 500RTS ANSI Operator Manual (46 pages)
- 800A_AJ Operator Manual (134 pages)
- 800A_AJ Operator Manual (150 pages)
- 266 Operator Manual (140 pages)
- G9-43A Parts Manual (788 pages)
- G6-42A Parts Manual (478 pages)
- M400AJP Narrow (108 pages)
- E400 Operator Manual (118 pages)
- 80HX_HX+6 ANSI Operator Manual (104 pages)
- 1350SJP Quick Reference Guide (1 page)
- 1350SJP Quick Reference Guide (2 pages)
- 15VPSP (3120798) Parts Manual (98 pages)
- X14J Operator Manual (169 pages)
- 400S ANSI Service Manual (464 pages)
- X17J Plus Operator Manual (176 pages)
- 20AM Operator Manual (98 pages)
- 3369LE Operator Manual (86 pages)
- 3369LE Operator Manual (84 pages)