Cable connection, Gprs) – Nokia E50 User Manual

Page 84

•

Use PPP compress.

— Select

Yes

to speed up the data transfer, if it is supported by the remote PPP server.

•

Use login script

— Select

Yes

, if your Internet service provider requires a login script, or if you want to automate your login.

A login script is a sequence of instructions that the system follows during the login process.

•

— Enter the login script. This setting is available only if you have selected

Use login script

Yes

•

Modem initialisation

— Enter a command string for the connection setup, if required by your service provider.

Set up an Internet access point for packet data (GPRS)

1. Select

Tools

Settings

Connection

Access points

2. Select

Options

New access point

. To use an existing access point as a basis for the new one, select

Use existing settings

. To

start with an empty access point, select

Use default settings

3. Define the following settings.

•

Connection name

— Enter a descriptive name for the connection.

•

Data bearer

— Select

Packet data

•

Access point name

— Enter the name for the access point. The name is usually provided by your service provider or network

operator.

•

User name

— Enter your user name if required by the service provider. User names are often case-sensitive and provided

by your service provider.

•

Prompt password

— Select

Yes

to enter your password each time you log into a server or

to save the password in your

device memory and automate the login.

•

Password

— Enter your password if required by the service provider. The password is often case-sensitive provided by

the service provider.

•

Authentication

— Select

Secure

to always send your password encrypted or

Normal

to send your password encrypted

when possible.

•

Homepage

— Enter the Web address of the page you want to display as a home page when you use this access point.

4. After defining the settings, select

Options

Advanced settings

to define the advanced settings or

Back

to save the settings

and exit.

Advanced Internet access point settings for packet data (GPRS)

After setting up a basic Internet access point for packet data (GPRS), select

Options

Advanced settings

, and define the following

advanced settings.
•

Network type

— Select

IPv4

IPv6

as the Internet protocol type. The Internet protocol defines how data is transferred to

and from your device.

•

Phone IP address

— Enter the IP address of your device. Select

Automatic

to have the network provide the device IP address.

This setting is shown only if you select

Network type

IPv4

•

DNS address

— Enter the IP addresses of the

Primary DNS address

and

Secondary DNS addr.

if required by your service provider

or network operator. Otherwise, the name server addresses are provided automatically.

•

Proxy serv. address

— Enter the address of the proxy server. Proxy servers are intermediate servers between a browsing

service and its users, which are used by some service providers. These servers may provide additional security and speed up

access to the service.

Cable connection

Install the USB data cable driver to your PC before you use a cable connection. You can use the

Data transfer

without installing

the USB data cable drivers.
Select

Connect.

Data cbl.

Using a USB data cable, you can connect your device to a compatible PC . Connect the USB data cable to the bottom of the device.

To change the device type you normally connect to your device with the data cable, press the joystick.
Select from the following:
•

Ask on connection

— Select whether you want to be asked for the device type every time you connect the data cable to your

device.

•

PC Suite

— Connect the PC Suite to your device with the data cable, and use your device as a modem.

•

Data transfer

— Access and transfer data such as music or image files from your computer using the data cable connection.

To use the

Data transfer

mode, make sure that you have not selected USB as a connection type in the Manage connections

settings in Nokia PC Suite. Insert a memory card to your device, connect the device to a compatible computer with the USB

data cable, and select

Data transfer

when the device asks which mode is used. In this mode, your device acts as a mass storage

device and you can see it as a removable hard drive in your computer. The device will switch into the

Offline

profile if this is

selected. End the connection from the PC (for example, from an Unplug or Eject Hardware wizard in Windows) to avoid

damaging the memory card. After you end the connection, the device returns to the profile in which it was before using the

data transfer mode.

To save your selection, select

Back

C o n n e c t i v i t y