AMX NetLinx Integrated Controllers NI-3000 User Manual
Netlinx integrated controllers
This manual is related to the following products:
Table of contents
Document Outline
- NetLinx Integrated Controller (NI-2000, NI-3000, and NI-4000)
- Introduction
- Quick Setup and Configuration Overview
- Connections and Wiring
- Setting the Configuration DIP Switch (for the Program Port)
- Modes and Front Panel LED Blink Patterns
- Wiring Guidelines
- Program Port Connections and Wiring
- RS-232/422/485 Device Port Wiring Specifications
- ICSNet RJ-45 Connections/Wiring
- Ethernet 10/100 Base-T RJ-45 Connections/Wiring
- Relay Connections and Wiring
- Input/Output (I/O) Connections and Wiring
- IR/Serial Connections and Wiring
- NetLinx Control Card Slot Connector (NI-4000 unit only)
- Installation and Upgrading
- Configuration and Firmware Update
- Communicating with the Master via the Program Port
- Setting the System Value
- Changing the Device Address on a NetLinx Device
- Resetting the Factory Default System and Device Values
- Obtaining the Master’s IP Address (using DHCP)
- Assigning a Static IP to the NetLinx Master
- Communicating with the On-board Master via an IP
- Verifying the current version of NetLinx Master Firmware
- Upgrading the On-board Master Firmware via an IP
- Upgrading the NI Controller Firmware via an IP
- Upgrading the Control Card Firmware via an IP
- NetLinx Security and Web Server
- NetLinx Security web browser and feature support
- New Master Firmware Security Features
- NetLinx Security Terms
- Accessing the NetLinx Master via its IP Address
- WebControl Tab
- Default Security Configuration
- Security Tab
- Security tab - Enable Security page
- Security tab - Add Group page
- Security tab - Modify Group page
- Security tab - Group Directory Associations page
- Security tab - Add User page
- Security tab - Modify User page
- Security tab - User Directory Associations page
- Security tab - SSL Server Certificate page
- Security tab - Export Certificate Request page
- Security tab - Import Certificate page
- System Tab
- Show Devices Tab
- Network Tab
- Master Security Setup Procedures
- Setting the system security options for a NetLinx Master (Security Options Menu)
- Adding a Group and assigning their access rights
- Modifying an existing Group’s access rights
- Showing a list of authorized Groups
- Deleting an existing Group
- Adding a Group directory association
- Confirming the new directory association
- Deleting a directory association
- Adding a User and configuring their access rights
- Modifying an existing User’s access rights
- Showing a list of authorized Users
- Deleting a User
- Adding a User directory association
- Confirming the new directory association
- Deleting a directory association
- SSL Certificate Procedures
- Common Steps for Requesting a Certificate from a CA
- Accessing an SSL-Enabled Master via an IP Address
- What to do when a Certificate Expires
- NetLinx Security with a Terminal Connection
- NetLinx Security Features
- Initial Setup via a Terminal Connection
- Accessing the Security configuration options
- Option 1 - Set system security options for NetLinx Master (Security Options Menu)
- Option 2 - Display system security options for NetLinx Master
- Option 3 - Add user
- Option 4 - Edit User
- Option 5 - Delete user
- Option 6 - Show the list of authorized users
- Option 7 - Add Group
- Option 8 - Edit Group
- Option 9 - Delete Group
- Option 10 - Show List of Authorized Groups
- Option 11 - Set Telnet Timeout in seconds
- Option 12 - Display Telnet Timeout in seconds
- Option 13 - Make changes permanent by saving to flash
- Main Security Menu
- Default Security Configuration
- Logging Into a Session
- Logout
- Programming
- Converting Axcess Code to NetLinx Code
- Using the ID Button
- Program Port Commands
- ESC Pass Codes
- Notes on Specific Telnet/Terminal Clients
- LED Disable/Enable Send_Commands
- RS-232/422/485 Send_Commands
- RS-232/422/485 Send_String Escape Sequences
- IR / Serial Ports Channels
- IR RX Port Channels
- IR/Serial Send_Commands
- Input/Output Send_Commands
- Troubleshooting