Dsp settings – Kenwood KDC-U7056BT User Manual
Page 7
14
|
KDC-U7056DAB/ KDC-U7056BT/ KDC-U7056BTL
English
|
15
DSP settings
4-4. Speaker setting
The speaker X’Over is automatically set when the
position and size of each speaker are selected from
the following items.
1
Press [SRC] to select a source other than
Standby (“STANDBY”).
Refer to
.
2
Press [Control] knob.
Enters the Function setting mode.
3
Select “Audio Control”
>
“Pro Setup”
>
“Speaker Setting” using [Control] knob.
For how to use [Control] knob, refer to
<3-3. How
to select the item> (page 9)
.
4
Select a speaker type using [Control] knob.
Speaker type Setting item Setting value
“Front”
Front speaker
location
“
Door
”, “On Dash”, “Under Dash”
“SIZE”
Front speaker size
“O.E.M.”, “8cm”, “10cm”, “12cm”,
“13cm”, “
16cm
”, “17cm”, “18cm”,
“4x6”, “5x7”, “6x8”, “6x9”, “7x10”
“TW”
Tweeter size
“None”, “Small”, “
Medium
”, “Large”
“Rear”
Rear speaker
location
“
Door
”, “Rear Deck”
(“
2nd Row
”, “3rd Row”
[1]
)
“SIZE”
Rear speaker size
“None”, “O.E.M.”, “8cm”, “10cm”,
“12cm”, “13cm”, “
16cm
”, “17cm”,
“18cm”, “4x6”, “5x7”, “6x8”, “6x9”,
“7x10”
“SubWoofer” “SIZE”
Speaker Size Subwoofer
“None”, “16cm”, “20cm”, “
25cm
”,
“30cm”, “38cm Over”
(
Colored text
: Factory setting)
[1]
Value set when “Minivan” or “Minivan (Long)” is selected
as described in
<4-3. Car type selection> (page 13)
.
When Speaker network is set to 3 way
Speaker type Setting item Setting value
“Tweeter”
“SIZE”
Tweeter size
“Small”, “
Medium
”, “Large”
“Mid Range”
Mid Range
speaker
location
Mid range speaker location
“
Door
”, “On Dush”, “Under Dush”
“SIZE”
Mid range speaker size
“O.E.M.”, “8cm”, “10cm”, “12cm”,
“13cm”, “
16cm
”, “17cm”, “18cm”,
“4x6”, “5x7”, “6x8”, “6x9”, “7x10”
“Woofer”
“SIZE”
Subwoofer size
“None”, “16cm”, “20cm”, “
25cm
”,
“30cm”, “38cm Over”
4-5. X’Over setting
Fine adjusting the following setting values
corresponding to the X’Over values set in the
section
<4-4. Speaker setting> (page 14)
.
1
Press [SRC] to select a source other than
Standby (“STANDBY”).
Refer to
.
2
Press [Control] knob.
Enters the Function setting mode.
3
Select “Audio Control”
>
“Pro Setup”
>
“X’Over” using [Control] knob.
For how to use [Control] knob, refer to
<3-3. How
to select the item> (page 9)
.
4
Select a speaker type using [Control] knob.
Speaker type Setting item Setting value
“Front”
“FC”
Front high pass filter
Through
, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 Hz
“SLOPE”
[1]
Front high pass slope
-6,
-12
, -18, -24 dB/Oct
“GAIN”
Front gain
-8 ,-7, -6, -5, -4, -3, -2, -1,
0
dB
“Rear”
“FC”
Rear high pass filter
Through
, 30, 40, 50, 60, 70, 80, 90,
100, 120, 150, 180, 220, 250 Hz
“SLOPE”
[1]
Rear high pass slope
-6,
-12
, -18, -24 dB/Oct
“GAIN”
Rear Gain
-8, -7, -6, -5, -4, -3, -2, -1,
0
dB
“SubWoofer” “FC”
Subwoofer low pass filter
30, 40, 50, 60, 70, 80, 90, 100, 120,
150, 180, 220, 250,
Through
Hz
“SLOPE”
[1]
Subwoofer slope
-6,
-12
, -18, -24 dB/Oct
“GAIN”
Subwoofer gain
-8, -7, -6, -5, -4, -3, -2, -1,
0
dB
“PHASE”
Subwoofer phase
“REV” (180°)/ “
NML
” (0°)
“Tweeter”
“FC”
Shelving filter
1, 1.6, 2.5,
4
, 5, 6.3, 8, 10, 12.5 kHz
“Volume”
Tweete volume
-8, -7, -6, -5, -4, -3, -2, -1,
0
dB
(
Colored text
: Factory setting)
[1]
Displayed only when “FC” is set to ”30” - “250”.
5
Select a setting item using [Control] knob.
6
Select a setting value using [Control] knob.
Exiting from the Function setting mode
Press and hold [
1/6].
When Speaker network is set to 3 way
Speaker type Setting item Setting value
“Tweeter”
“FC”
Tweeter high pass filter
1, 1.6, 2.5,
4
, 5, 6.3, 8, 10, 12.5 kHz
“SLOPE”
Tweeter slope
-6,
-12
dB/Oct
“GAIN”
Tweeter gain
-8 ,-7, -6, -5, -4, -3, -2, -1,
0
dB
“PHASE”
Tweeter phase
“REV” (180°)/ “
NML
” (0°)
“Mid LPF”
“FC”
Mid range low pass filter
1, 1.6, 2.5,
4
, 5, 6.3, 8, 10, 12.5,
Through kHz
“SLOPE”
Mid range low pass slope
-6,
-12
dB/Oct
“GAIN”
Mid range gain
-8, -7, -6, -5, -4, -3, -2, -1,
0
dB
“PHASE”
Mid range phase
“REV” (180°)/ “
NML
” (0°)
“Mid HPF”
“FC”
Mid range high pass filter
Through, 30, 40, 50, 60, 70, 80, 90,
100
, 120, 150, 180, 220, 250 Hz
“SLOPE”
Mid range high pass slope
-6,
-12
dB/Oct
“GAIN”
Mid range gain
-8, -7, -6, -5, -4, -3, -2, -1,
0
dB
“PHASE”
Mid range phase
“REV” (180°)/ “
NML
” (0°)
“Woofer”
“FC”
Woofer low pass filter
30, 40, 50, 60, 70, 80, 90,
100
, 120,
150, 180, 220, 250, Through Hz
“SLOPE”
Woofer low pass slope
-6,
-12
dB/Oct
“GAIN”
Woofer gain
-8, -7, -6, -5, -4, -3, -2, -1,
0
dB
“PHASE”
Woofer phase
“REV” (180°)/ “
NML
” (0°)
5
Select a setting item using [Control] knob.
6
Select a setting value using [Control] knob.
Exiting from the Function setting mode
Press and hold [
1/6].