Thread turning infeed recommendations, Iso inch (un), internal, Technical reference – Sandvik Coromant Threading User Manual
Page 99
99
32
28
24
20
18
16
14
13
12
11
10
9
8
7
6
5
4.5
4
1
0.16 0.14 0.16 0.16 0.18 0.17 0.16 0.18 0.20 0.19 0.19 0.19 0.19 0.23 0.21 0.27 0.28 0.30
.006 .005 .006 .006 .007 .007 .006 .007 .008 .008 .007 .007 .008 .009 .008 .011 .011 .012
2
0.14 0.13 0.15 0.15 0.17 0.16 0.16 0.17 0.19 0.18 0.18 0.18 0.19 0.22 0.21 0.26 0.27 0.29
.006 .005 .006 .006 .007 .006 .006 .007 .008 .007 .007 .007 .007 .009 .008 .010 .011 .011
3
0.13 0.12 0.14 0.14 0.16 0.15 0.15 0.16 0.18 0.18 0.17 0.18 0.18 0.21 0.20 0.25 0.27 0.28
.005 .005 .006 .006 .006 .006 .006 .006 .007 .007 .007 .007 .007 .008 .008 .010 .010 .011
4
0.08 0.11 0.12 0.13 0.14 0.14 0.14 0.16 0.17 0.17 0.17 0.17 0.18 0.21 0.20 0.25 0.26 0.27
.003 .004 .005 .005 .006 .006 .006 .006 .007 .007 .007 .007 .007 .008 .008 .010 .010 .011
5
0.08 0.08 0.12 0.13 0.13 0.14 0.15 0.16 0.16 0.16 0.16 0.17 0.20 0.19 0.24 0.25 0.27
.003 .003 .005 .005 .005 .005 .006 .006 .006 .006 .006 .007 .008 .008 .009 .010 .011
6
0.08 0.08 0.12 0.13 0.13 0.14 0.15 0.15 0.16 0.16 0.19 0.19 0.23 0.25 0.26
.003 .003 .005 .005 .005 .006 .006 .006 .006 .006 .007 .007 .009 .010 .010
7
0.08 0.11 0.12 0.13 0.14 0.14 0.15 0.16 0.18 0.18 0.22 0.24 0.25
.003 .004 .005 .005 .005 .006 .006 .006 .007 .007 .009 .009 .010
8
0.08 0.08 0.08 0.12 0.13 0.14 0.15 0.17 0.18 0.21 0.23 0.24
.003 .003 .003 .005 .005 .005 .006 .007 .007 .008 .009 .010
9
0.08 0.12 0.13 0.14 0.16 0.17 0.20 0.22 0.23
.003 .005 .005 .006 .006 .007 .008 .009 .009
10
0.08 0.11 0.13 0.14 0.16 0.19 0.21 0.22
.003 .004 .005 .006 .006 .008 .008 .009
11
0.08 0.11 0.12 0.15 0.18 0.20 0.21
.003 .005 .005 .006 .007 .008 .008
12
0.08 0.08 0.14 0.17 0.19 0.20
.003 .003 .006 .007 .008 .008
13
0.13 0.15 0.18 0.19
.005 .006 .007 .007
14
0.10 0.10 0.16 0.17
.004 .004 .006 .007
15
0.15 0.15
.006 .006
16
0.10 0.10
.004 .004
0.51
0.58
0.66
0.78
0.86
0.96
1.07
1.15
1.25
1.36
1.48
1.64
1.85
2.10
2.43
2.92
3.46
3.64
.020
.023
.026
.031
.034
.038
.042
.045
.049
.054
.058
.065
.073
.083
.096
.115
.136
.143
CMC 02.1
MC P2.1.Z.AN
5. Technical reference
Extra stock is included in the total infeed 0.05 mm
.002 inch
Reference material
ISO inch (UN), internal
Pitch, t.p.i.
No. of
infeeds
Unit
Radial infeed per pass
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
Total infeed
mm
inch
Thread turning infeed recommendations