ididit Retrofit Steering Column: 1962-66 Nova User Manual
Page 7

5
Once the column is in place install
the upper and lower halves of the
dash mount loosely. (Figure 3)
Rack and pinion Installation:
Slide the gasket & floor mount
down the column tube with the
prongs of the floor mount facing
towards the engine compartment.
Align the floor mounts screw holes
with the original holes in the floor.
Align the gasket and install the 4
screws with the large washers.
Make sure the dash mount’s
alignment tab is engaged and
secure the mount with its two
fasteners. (Figure 3) Tighten the
two bolts that hold the column to
the dash. Now, from the engine
side install the clamp around the
column and the two tabs and tighten.
(Figure 4)
For the rack column, the lower interior
rubber trim piece (Figure 5A) will
have to be modified as there is no
way to slide the grommet into the
floor mount Figure 5B is the finished
trimmed part ready for installation.
Install the gasket loosely. Put a dab
of silicone or trim adhesive on the
inside where it meets the column to
secure it. You may want to put a piece of
tape around the grommet for 24 hours or
until it dries. Figure 6 shows the trimmed
part properly installed.
(Figure 3)
(Figure 4)
A
(Figure 5)
B
(Figure 6)
- Universal Steering Column: How To Measure An ididit Steering Column (2 pages)
- Universal Steering Column: Universal Tilt (8 pages)
- Universal Steering Column: Universal Shorty Tilt (8 pages)
- Universal Steering Column: Universal Straight (8 pages)
- Universal Steering Column: Old School Straight Column (4 pages)
- Universal Steering Column: Old School Straight Horn Kit (4 pages)
- Retrofit Steering Column: Tri-Five Chevy (18 pages)
- Retrofit Steering Column: 1970-75 Camaro (12 pages)
- Retrofit Steering Column: 1955-59 Chevy Truck (12 pages)
- Retrofit Steering Column: 1965-66 Mustang (8 pages)
- Retrofit Steering Column: 1967 Mustang (8 pages)
- Retrofit Steering Column: 1968-69 Mustang (8 pages)
- Retrofit Steering Column: 1965 Falcon (12 pages)
- Retrofit Steering Column: 1965 Mercury Comet (8 pages)
- Retrofit Steering Column: 1965-66 Ford Truck (8 pages)
- Retrofit Steering Column: 1967-72 Ford Truck (8 pages)
- Retrofit Steering Column: 1973-77 Ford Truck (8 pages)
- Retrofit Steering Column: 1978-79 Ford Truck (8 pages)
- Retrofit Steering Column: 1974-77 Ford Bronco (8 pages)
- Retrofit Steering Column: 1976-86 Jeep CJ5 & CJ7 (12 pages)
- Retrofit Steering Column: Jeep Column to a Painless Wiring Kit (1 page)
- Retrofit Steering Column: 1970-74 Cuda/Challenger (12 pages)
- Retrofit Steering Column: 1970-74 Cuda/Challenger Ignition Switch (1 page)
- Retrofit Steering Column: 1970-74 Cuda/Challenger Wheel Adaptor (1 page)
- Retrofit Steering Column: 1967-69 Chrysler B-Body (8 pages)
- Retrofit Steering Column: 1968 Chrysler B-Body Adaptor Plug (1 page)
- Retrofit Steering Column: 1973 Chrysler B-Body (12 pages)
- Right Hand Drive & Collapsible Steering Column: Theory of a Collapsible Column (2 pages)
- Right Hand Drive & Collapsible Steering Column: RHD Universal Tilt (8 pages)
- Right Hand Drive & Collapsible Steering Column: RHD Tri-Five Chevy (16 pages)
- Right Hand Drive & Collapsible Steering Column: RHD 1965-66 Mustang (8 pages)
- Right Hand Drive & Collapsible Steering Column: RHD 1968-69 Mustang (8 pages)
- Golf Cart Steering Column: Club Car (1 page)
- Golf Cart Steering Column: E-Z Go (1 page)
- Golf Cart Steering Column: Yamaha (2 pages)
- Golf Cart Steering Column: Golf Cart 9-Bolt Steering Wheel Adaptor (1 page)
- Golf Cart Steering Column: Flasher Kit (1 page)
- Golf Cart Steering Column: Golf Cart Wiring (1 page)
- Steering Wheel Adaptor: Basic Adaptor (1 page)
- Steering Wheel Adaptor: 3-Bolt Standard Adaptor (1 page)
- Steering Wheel Adaptor: 3-Bolt Bell Adaptor (1 page)
- Steering Wheel Adaptor: 3-Bolt Bell/Grant Wheel w/Horn Kit (1 page)
- Steering Wheel Adaptor: 9-Bolt Shorty Adaptor (1 page)
- Steering Wheel Adaptor: 1953-66 Corvette Adaptor (1 page)