ADTRAN Express 4100 User Manual
ADTRAN Hardware
Table of contents
Document Outline
- Quick Startup Guide
- Chapter 1 Understanding ISDN and the Express 4100/4110
- ISDN Overview
- The Express 4100/4110
- Chapter 2 Installation
- Chapter 3 Terminal Menu Operation and Structure
- Terminal Menu Structure
- Navigating the Terminal Menus
- Configuration Menu
- Configuration/System Info
- Configuration/WAN
- Configuration/IP
- Configuration/IPX
- Configuration/Bridge
- Configuration/Security
- Configuration/Connection List
- Configuration/Management
- Configuration/Terminal Mode
- Dial Menu
- Status Menu
- Test Menu
- Logs Menu
- Utilities Menu
- Chapter 4 Troubleshooting
- Chapter 5 Specifications
- Appendix A Loop Status Messages
- AutoSpid Download
- AutoSpid X
- CALL
- Call Connect B1
- Call Connect B2
- Call Connect B1/B2
- Connected 64K/2X64K/128K
- DISCONNECTING
- DMS-100 Ready
- Echo: Tx: X Rx: Y
- Getting TEI #1
- Getting TEI #2
- ISDN-1 Ready
- Layer 1 up
- Link down
- Link In Sync
- LUCENT-5ESS Ready
- NET EOC LOOPBACK
- Register SPID #1
- Register SPID #1
- RINGING
- 56K
- 64K
- Audio
- Dialing
- Holding
- Idle
- Speech
- Release
- Retriv
- Ringing
- Routing
- Waiting
- Appendix B Log Messages
- B-Channels bundled
- BACP
down - BACP
up - BCP
down - BCP
up - Can't find user profile
- CCP
down - CCP
up - CHAP authen failed
- EAP authen failed
- IPCP
down - IPCP
up - IPXCP
down - IPXCP
up - LCP
down - LCP
up - Link is looped back
- MP options not the same
- Negot not converging
- No IP addr for peer
- No more bundles avail
- No Response from peer
- PAP authen failed
- Peer failed CHAP authen
- Peer failed EAP authen
- Peer failed PAP authen
- Peer refused authen
- Peer refused SpanTree
- PPPtx[x] …
- PPPrx[x] …
- Answer
- AutoSpid Download Not Available
- AutoSpid Download Pass
- AutoSpid Download Started
- AutoSpid Failed
- AutoSpid Passed
- AutoSpid Retry
- AutoSwitch LUCENT
- AutoSwitch DMS
- AutoSwitch NI-1
- Bad call type
- Bad Host_Call_ID
- Bad phone number
- Bandwidth drop
- Bandwidth request
- Bandwidth Restore
- Bearer Info Cap Incorrect
- Bearer Mode Incorrect
- BUSY
- Call lost
- Caller ID mismatch
- CallID 1 in use
- CallID 2 in use
- Can't answer, Call not ringing
- Cause: ‘
’ diag= - Conference
- Conference Rej
- Connect Timeout
- Connected
- Demand calling ‘
’ - DEST NOT ISDN
- Dial
- Dialing ...
- Disconnect
- Dump
- Dump call
- Fallback to 56K
- FarDN=
- Hangup
- Hold
- Hold Reject
- Idle timeout
- L1 not up
- L2 not up
- L2 #2 not up
- L3 not up
- L3 #2 not up
- LDN TOO LONG
- NETWORK BUSY
- Network down
- Network up
- No calling ID
- No previous number
- NOT end2end ISDN
- Power Up - last down cause:
- Probe: all ports busy
- Probe failed
- Probing
- POTS call bump
- Retrieved
- Ring
- SOURCE NOT ISDN
- Signal 0xNN
- Transfer
- Transfer Rej
- Attempting to add bad IP iface route: ifnum=
dest= - DHCP couldn't alloc mem
- DHCP response sent
- DHCP socket failed
- DHCP: Host not added to ARP table
- Installing bad default route: ifnum=
metric= gw= - Rejecting packet with Source Routing option - src=
dest= - setmask: local IP iface(0), not done
- syslog: bad host
- syslog: no port
- TEL: Telnet Session Closed
- telclient bad host
- telclient bad init
- Telnet Client: Clr TCBF_BUFFER flag failed
- Telnet Client: Set TCBF_DONTBLOCK flag failed
- Telnet Client socket failed
- Telnet server connect to
- Telnet Session Closed
- Telnet Session failed, error
- TELNETD: accept failed
- TELNETD: Set TCPC_LISTENQ failed
- TELNETD: Clr TCBF_BUFFER flag failed
- TELNETD: could not obtain peer IP
- TELNETD: Session failed, error
- TELNETD: Set TCBF_DONTBLOCK flag failed
- TELNETD: SOCKET creation error
- TFTP: can't get to host
- TFTP client: unable to open port
- TFTP: error rcvd -
" - TFTP: lost communication
- TFTP server: unable to open port
- Appendix C SNMP
- Appendix D Connector Pinouts
- Appendix E Terminal Mode Commands
- Appendix F Frame Relay Firmware Version
- Glossary
- Acronyms
- Index