Magstop, Components d-drive spacer removal/installation, Figure 1 figure 2 – Warner Electric TG-2000 MagStop Clutch_Brake User Manual
Page 4
4
Warner Electric • 800-825-9050
P-1177 • 819-0457
Figure 1
Figure 2
MagStop
®
Components
D-drive Spacer Removal/Installation
D-drive spacer may be installed on either end of clutch by OEM.
D-drive spacer must be removed or installed using an arbor press or equivalent.
On installation, opposite bearing INNER race must be supported or bearing damage may occur.
On removal, adjacent bearing OUTER race must be supported or bearing damage may occur.
D-drive Spacer removal
D-drive Spacer installation
Washer
Diameter
Must Not
Exceed OD
of Bearing
Inner Race.
Optional
Washer
.250 Inch
(6.35 mm)
Minimum
Washer
Thickness.
Coil
One piece
Field Assembly
D-drive
Spacer
Armature
Assembly
Field
Bearing
Armature
Bearing
Brake Poles
Rotor
Assembly
Armature Leaf
Springs
2
Anti-
Rotation
Slot
Top View
One Piece Field Assembly with
Integral Anti-Rotation Slots
Field
Assembly
Support bearing
inner race
D-drive Spacer
Press
Support bearing outer race
D-drive Spacer
Press
- UNIBRAKE NEMA 4 (6 pages)
- UNIBRAKE (8 pages)
- ARC 2000 (16 pages)
- ARC Clutch_ZRC Top Load (18 pages)
- ZRC Clutch_ARC Top Load (18 pages)
- Dairy Cap Chuck (24 pages)
- Dairy Capping Headsets (10 pages)
- Autogap 475 & 650 (4 pages)
- Brushholder Installation (2 pages)
- Autogap 825-1225 (2 pages)
- Electro-Packs EP-170, 250, 400, 500, 825, 1000, 1525 (20 pages)
- Electro-Brake 375, 475, 650, 825, 1000, 1225 (20 pages)
- Electro-Clutch EC-375, EC-475, EC-650, EC-825, EC-1000, EC-1225 (20 pages)
- 5300-101-001 Collector Ring (2 pages)
- 5301-101-010 Collector Ring (2 pages)
- Brushholder Assembly and Mounting Dimensions (2 pages)
- SF_PB 400 (2 pages)
- SF_PB 250 (2 pages)
- Autogap 825-1525 (4 pages)
- Electro-Module EM-50, EM-100, EM-180, EM-210, EM-215 (22 pages)
- FB-375, 475, 650 (14 pages)
- 5200-101-012 Conduit Box Kit (4 pages)
- 5200-101-011 Conduit Box Kit (4 pages)
- 5200-101-010 Conduit Box Kit (4 pages)
- Recommended Electrical Installation Procedure for Warner Electric Clutches and Brakes (2 pages)
- EP-400 Vertical Mounting (2 pages)
- EP-250 Vertical Mounting (2 pages)
- Autogap 500 (4 pages)
- ER 825 and 1225 Normal Duty (16 pages)
- ER 825 and 1225 Heavy Duty (14 pages)
- ERS Electrically Released Brakes (6 pages)
- AT Brakes & Clutches Complete Brake Repair – On the Shaft, Sizes 25, 55, 115 (4 pages)
- AT Brakes (6 pages)
- AT Brake–Major Service Repair Instructions for Sizes 25, 55, 115 (9 pages)
- AT Clutch – Major Service Sizes 25, 55, 115 (12 pages)
- 5162-101-002 Conduit Box Kit (6 pages)
- Electrically Released Permanent Magnet Clutch Compatible Modules (4 pages)
- Electrically Released Motor Brake Module for EM-MBFB and EUM-MBFB (6 pages)
- Electrically Released Brake Module For EM-FBB and EUM-FBB (4 pages)
- Electrically Released Brake ER-375, ER-475, ER-650 (12 pages)
- Autogap 825-1525 Special Heavy Duty (4 pages)
- 5370-101-042 Conduit Box Kit (4 pages)
- Preassembled Clutch_Electrically Released Brake Module (7 pages)
- EUM-50_EUM-100_EUM-180_EUM-210_EUM-215 (16 pages)
- 5370-101-045 Conduit Box Kit (5 pages)