Warner Electric Brushholder Assembly and Mounting Dimensions User Manual
Installation instructions
Warner Electric Brushholder
Assembly and Mounting Dimensions
Installation Instructions
P-1369
819-0032
2
0.56
(14.22)
0.75
(19.05)
1.41
(35.81)
1.56
(39.69)
0.78
(19.84)
1.72
(42.69)
1.34
(34.03)
By
Customer
By
Customer
1.88
(47.8)
1.31
(33.34)
0.75
(19.05)
0.38
(9.53)
0.75
(19.05)
0.38
(9.53)
0.188
(4.78)
4 holes tapped for #8-32 screws
(by customer) to enter brushholder
case 0.31 (7.87) max.
Rotation
1/2 standard
straight pipe
tap 0.391 (9.93)
deep
Dimension “A” for collector ring: 5301-101-001 is 4.00 (101.6)
to of shaft. 5301-749-001 is 5.75 (146.05) to of shaft.
Brushholder may be mounted at one end opposite conduit or
from either side. It is recommended that brushes be assembled
so that the arrow on brushes points in the direction of rotation
of the collector ring, however brushholder may be used with
reversing clutch.
Dim.
“A”
1.03
(26.16)
0.28
(7.11)
1
Alternate Mounting
0.188 (4.76) dia. 2 holes thru
screws and nuts by customer
1
2
5300-178-001 Brushholder Assembly
176-0001
Brush
Warner Electric • 800-825-9050
P-1369 • 819-0032
- UNIBRAKE NEMA 4 (6 pages)
- UNIBRAKE (8 pages)
- ARC 2000 (16 pages)
- ARC Clutch_ZRC Top Load (18 pages)
- ZRC Clutch_ARC Top Load (18 pages)
- Dairy Cap Chuck (24 pages)
- Dairy Capping Headsets (10 pages)
- Autogap 475 & 650 (4 pages)
- Brushholder Installation (2 pages)
- Autogap 825-1225 (2 pages)
- Electro-Packs EP-170, 250, 400, 500, 825, 1000, 1525 (20 pages)
- Electro-Brake 375, 475, 650, 825, 1000, 1225 (20 pages)
- Electro-Clutch EC-375, EC-475, EC-650, EC-825, EC-1000, EC-1225 (20 pages)
- 5300-101-001 Collector Ring (2 pages)
- 5301-101-010 Collector Ring (2 pages)
- SF_PB 400 (2 pages)
- SF_PB 250 (2 pages)
- Autogap 825-1525 (4 pages)
- Electro-Module EM-50, EM-100, EM-180, EM-210, EM-215 (22 pages)
- FB-375, 475, 650 (14 pages)
- 5200-101-012 Conduit Box Kit (4 pages)
- 5200-101-011 Conduit Box Kit (4 pages)
- 5200-101-010 Conduit Box Kit (4 pages)
- Recommended Electrical Installation Procedure for Warner Electric Clutches and Brakes (2 pages)
- EP-400 Vertical Mounting (2 pages)
- EP-250 Vertical Mounting (2 pages)
- Autogap 500 (4 pages)
- ER 825 and 1225 Normal Duty (16 pages)
- ER 825 and 1225 Heavy Duty (14 pages)
- ERS Electrically Released Brakes (6 pages)
- AT Brakes & Clutches Complete Brake Repair – On the Shaft, Sizes 25, 55, 115 (4 pages)
- AT Brakes (6 pages)
- AT Brake–Major Service Repair Instructions for Sizes 25, 55, 115 (9 pages)
- AT Clutch – Major Service Sizes 25, 55, 115 (12 pages)
- 5162-101-002 Conduit Box Kit (6 pages)
- Electrically Released Permanent Magnet Clutch Compatible Modules (4 pages)
- Electrically Released Motor Brake Module for EM-MBFB and EUM-MBFB (6 pages)
- Electrically Released Brake Module For EM-FBB and EUM-FBB (4 pages)
- Electrically Released Brake ER-375, ER-475, ER-650 (12 pages)
- Autogap 825-1525 Special Heavy Duty (4 pages)
- 5370-101-042 Conduit Box Kit (4 pages)
- Preassembled Clutch_Electrically Released Brake Module (7 pages)
- EUM-50_EUM-100_EUM-180_EUM-210_EUM-215 (16 pages)
- 5370-101-045 Conduit Box Kit (5 pages)