Gilderfluke&Co Pb-DMX - Manual (Page 42)

FCC and CE Compliance:
Pb-DMX/32s which are hardware revision 3.0 or later have
been tested to comply with FCC and CE requirements. Revi-
sions earlier than this may have passed testing, but were not
certified at the time of manufacture.
Because Pb-DMX/32s are low voltage DC devices, neither
UL or CE require safety testing.
For fireproofing or additional radio frequency interference
shielding, Pb-DMX/32s can be mounted in a fire rated metal-
lic case. Typically, this would be a NEMA-rated electrical en-
closure or 19” electrical rack.
FCC Instruction to User:
This equipment has been tested and found to comply with the
limits for a class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential instal-
lation. This equipment generates, uses and can radiate radio
frequency energy and if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that inter-
ference will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the inter-
ference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and re-
ceiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
This equipment has been verified to comply with the limits for
a class B computing device, pursuant to FCC Rules. In order
to maintain compliance with FCC regulations, shielded cables
must be used with this equipment. Operation with non-
approved equipment or unshielded cables is likely to result in
interference to radio and TV reception. The user is cautioned
that changes and modifications made to the equipment with-
out the approval of manufacturer could void the user's author-
ity to operate this equipment.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference and (2) this device must accept any
interference received, including interference that
may cause undesired operation.
This Class B digital apparatus meets all require-
ments of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numerique de la classe B respecte
toutes les exigences du Reglement sur le
materiel brouilleur du Canada.
EC DECLARATION OF CONFORMITY
Thursday, October 31, 2013
Application of Council Directives:# # # # EMC Directive, 89/336/EEC
Manufacturer's Name:# # # # # Gilderfluke & Co., Inc.
Manufacturerʼs Address:# # # # # 205 South Flower St., Burbank, California 91502 USA
Importerʼs Name:# # # # # # # # # # # # #
Importerʼs Address:# # # # # # # # # # # # #
Type of Equipment:# # # # # # Entertainment and Lighting Control
Equipment Class:# # # # # # Commercial and Light Industrial
Model:# # # # # # # Pb-DMX/32
Conforms to the following Standards:# # # EN 55103-1: 1996 and EN 55103-2: 1996
Year of Manufacture:# # # # # 2006
I the undersigned, hereby declare that the equipment specified above conforms to the above directive(s)
and standard(s).
Place:#Burbank, California# # # # # Signature:# (signed)# # # #
Date: August 1, 2006# # # # # Full Name:# Doug Mobley
# # # # # # # # Position:# CEO
Gilderfluke & Co.• 205 South Flower Street • Burbank, California 91502 • 818/840-9484 • 800/776-5972 • fax 818/840-9485
Pb-DMX/32 v1.+ Manual / 10/31/13 / page 36 of 37