intimus Modelis 684 - Manual (Page 5)

MAINTENANCE / DISPOSING
5
COMPENSATION OF THE LIGHT BARRIER:
In order to eliminate malfunctions due to chan-
ging light conditions at the inlet aperture (e.g.
by changing the location) or due to the wear
of the fotocell (scratches), the sensitivity of the
light barrier is automatically
re-adjusted by the
machine for the detection of „normal“ paper in
regular intervals.
This so called „compensation“ can also be carried
out
manually in accordance with the sequence
described in the following (e. g. after change of
the light barrier or the PC Board).
The „receptacle full“ switch-off must not be ac-
tivated for the re-adjustment. The procedure is
as follows:
1. Switch off the maschine at the pushbutton switch
(1) and open the door.
2. Press the pushbutton switch „reverse“ (3) and
keep it pressed.
3. Press the „ready“ pushbutton switch (1).
4. Release the „reverse“ pushbutton switch (3)
after approx. 3 sec.
5. (This process is only required for the cross-cut
models.)
Push switching flap „receptacle full“ backwards
for at least 3 sec.
6. Close the door after approx. 3 sec.
7. Cover the light barrier with a piece of paper (do
not feed the paper up to the cutter) and wait
until the motor is switched on.
This completes the compensation. The machine
is now ready for operation.
Note: If the compensation process has been
interfered with due to exessive external incident
light (direct sun light, lamps, spots etc.) or due to
a false procedure, keep the external light away
from light barrier and re-start the compensation
process right from the beginning.
CLEANING THE PHOTOCELLS (fig. 5):
If paper particles should come to rest in the inlet
guide (for example after a paper jam) it is pos-
sible that the machine will not turn off, due to the
broken light barrier.
To remove these paper strips and also to clean
the photocell, pass another sheet of paper through
the feed slot, or switch the machine to reverse and
wipe both „eyes“ of the photocell with a brush.
MAINTENANCE CUTTING BLOCK:
(cross-cut)
After approximately 15 minutes of con-
tinuous use, run the cutting system in
reverse for 15 to 20 seconds and spray
some of the enclosed Special Oil onto the
cutting system.
TIP FOR ENERGY SAVING:
Please make sure that the shredder is switched off
over night (pushbutton switch (1) (fig. 1).
DISPOSING OF THE MACHINE:
Dispose of the machine in an
environmentally sound fashion at the
end of its useful service life. Do not
dispose of any of the parts included
in the machine or its packaging with
household trash.
TECHNICAL DATA
MALFUNCTIONS
PAPER JAM:
If too much paper is fed to the cutting system the
machine will react as follows:
- The cutting system blocks, reverses a bit to
release the paper and then stops.
- The motor shuts down automatically.
- The pilot lamp (6) (fig. 1) lights up.
Proceed as follows:
- Briefly operate the pushbutton switch for reverse
(3) (fig. 1).
- The pilot lamp (6) (fig. 1) goes off.
- Remove excess paper from the machine and
continue shredding with less paper.
MOTOR PROTECTION:
The motor shuts down automatically, should it
become overloaded. Turn the machine off with
the pushbutton switch (1) (fig. 1).
Allow the motor to cool down for 15 to 20 minutes
(depending upon room temperature) and then
continue shredding.
CHECKLIST IN CASE OF MALFUNCTIONS:
If the device does not function, check the follo-
wing:
- Is the
plug connected to the mains?
Mains connection: 2-pole mains switch,
internal appliance plug,
separate power cord
- Is the pushbutton switch (1) on?
- Is the door closed?
- Is the receptacle full?
The receptacle has to be emptied.
- Is there a
paper jam?
Follow the instructions under „paper jam“.
- has the
motor been overloaded?
Wait until the motor has cooled, and then re-
start.
If none of the above applies, please contact
your dealer.
ACCESSORIES
Cutting width:
452/502/602:
3.8 mm (strips)
502/602: 5.8 mm (strips)
452CC/502CC/602CC: 1.9x15 mm (cross-cut)
502CC/602CC:
3.8x36 mm (cross-cut)
502HS/602HS: 0.8x12 mm (cross-cut)
502SF/602SF: 0.8x4.5 mm (cross-cut)
Cutting capacity:
452:
15-17 sheets (70g/m 2 )
452CC: 10-12 sheets (70g/m 2 )
502:
3.8 mm:
23-25 sheets (70g/m 2 )
5.8 mm: 31-33 sheets (70g/m 2 )
502CC:
1.9x15 mm:
13-15 sheets (70g/m 2 )
3.8x36 mm: 18-20 sheets (70g/m 2 )
502HS: 8-10 sheets (70g/m 2 )
502SF: 5-6 sheets (70g/m 2 )
602:
3.8 mm:
23-25 sheets (70g/m 2 )
5.8 mm: 27-33 sheets (70g/m 2 )
602CC:
1.9x15 mm:
13-16 sheets (70g/m 2 )
3.8x36 mm: 20-22 sheets (70g/m 2 )
602HS: 8-10 sheets (70g/m 2 )
602SF: 5-6 sheets (70g/m 2 )
Supply voltage: 230V/50Hz
240V/50Hz
120V/60Hz
100V/50/60Hz
Pre-fusing:
230V/240V/50Hz:
10 amps (slow-blow)
120V/100V/50/60Hz: 20 amps (slow-blow)
Working width:
452/CC:
405 mm
502/CC/HS/SF: 260 mm
602/CC/HS/SF: 405 mm
Noise level: approx. 54 dB(A)
Power:
452/CC:
1.1/0.9 kW
502/CC/HS/SF: 1.1/1,5 kW
602/CC/HS/SF: 1.1 kW
Dimensions (WxDxH):
452/CC:
660x430x880 mm
502/CC/HS/SF: 490x380x870 mm
602/CC/HS/SF: 660x430x1020 mm
Weight:
452/CC:
ca. 60 kg
502/CC/HS/SF: ca. 41-43 kg
602/CC/HS/SF: ca. 60 kg
fig. 5
Description Order-No.
Plastic bag, 440 x 330 x 950 x 0,05 mm (502/CC/HS/SF) 99977
Plastic bag, 600 x 500 x 1000 x 0,05 mm (452CC // 602/CC/HS/SF) 99952
Lubricant, 125 ml bottle (cross-cut) 99943
Feeding mechanism for computer paper (452CC // 602/CC/HS/SF) 81942
Note: For orders of special accessories and spare parts, please contact your dealer.
GB
452 452CC 502 502CC 502HS 502SF 602 602CC 602HS 602SF
2