Atec Kikusui-TOS9201 - Manual (Page 9)

12 Kikusui Electronics Corporation
TOS9200 SERIES
Hipot Tester with Insulation Resistance Test
Item TOS9200 TOS9201
Judgement function
Judgement method/action
• The PASS signal is output at the timing preset on PASS HOLD. If HOLD is set, the PASS signal is output continuously until
the STOP signal is input.
• The UPPER FAIL signal and the LOWER FAIL signal are output continuously until the STOP signal is input.
• The FAIL and PASS buzzer volumes are adjustable. However, they cannot be adjusted individually, as they are set in common.
Setting range for the upper resistance (UPPER) 0.01 M Ω to 9.99 GΩ [Below the maximum rated current]
Setting range for the lower resistance (LOWER) 0.01 M Ω to 9.99 GΩ [Below the maximum rated current]
Judgement accuracy
For both UPPER and LOWER
Time
Setting range for the voltage rise time (RISE TIME) 0.1 s to 200 s
Setting range for the test time (TEST TIME) 0.5 s to 999 s With the TIMER OFF function
Setting range for the judgement wait time (WAIT TIME) 0.3 s to 10 s [RISE TIME + TEST TIME > WAIT TIME]
Accuracy ± (100 ppm + 20 ms)
* 5 When the GND is set to GUARD, current measurement is disabled if the part of the DUT connected to the LOW terminal is grounded, which poses extreme danger. Never ground the DUT.
In ordinary operation, set the GND to LOW.
Judgement Judgement method Display Buzzer SIGNAL I/O
UPPER FAIL When the tester detects a resistance exceeding the upper cutoff resistance,
it cuts off the output and makes an UPPER FAIL judgement. However,
no judgement is made during a voltage rise time (RISE TIME).
The FAIL
LED lights up.
Displayed
on the LCD
ON Outputs the
U FAIL signal
LOWER FAIL When the tester detects a resistance below the lower cutoff resistance,
it cuts off the output and makes a LOWER FAIL judgement. However,
no judgement is made until the judgement wait time (WAIT TIME)
has elapsed.
The FAIL
LED lights up.
Displayed
on the LCD
ON Outputs the
L FAIL signal
PASS When the preset time has elapsed without any abnormalities,
the tester cuts off the output and makes a PASS judgement.
The PASS
LED lights up.
Displayed
on the LCD
ON Outputs the
PASS signal
Judgement current 50 nA ≤ i ≤ 100 nA 100 nA < i ≤ 200 nA 200nA < i ≤ 1 μA 1 μA < i ≤ 1 mA
UPPER, LOWER 0.01 ≤ R < 10.0 MΩ –– –– –– ± (2 % of setting + 3digit)
10.0 ≤ R < 50.0 MΩ –– –– ± (5 % of setting + 5digit) ± (2 % of setting + 3digit)
50.0 ≤ R < 100 MΩ –– –– ± (5 % of setting + 5digit) ± (2 % of setting + 3digit)
100 M Ω ≤ R < 200 MΩ –– ± (10 % of setting + 5digit) ± (5 % of setting + 5digit) ± (2 % of setting + 3digit)
200 M Ω ≤ R < 500 MΩ ± (20 % of setting + 5digit) ± (10 % of setting + 5digit) ± (5 % of setting + 5digit) ± (2 % of setting + 3digit)
500 M Ω ≤ R < 1.00 GΩ ± (20 % of setting + 5digit) ± (10 % of setting + 5digit) ± (5 % of setting + 5digit) ± (2 % of setting + 3digit)
1.00 G Ω ≤ R < 2.00 GΩ ± (20 % of setting + 10digit) ± (10 % of setting + 5digit) ± (5 % of setting + 5digit) ––
2.00 G Ω ≤ R < 5.00 GΩ ± (20 % of setting + 20digit) ± (10 % of setting + 10digit) ± (5 % of setting + 5digit) ––
5.00 G Ω ≤ R < 10.0 GΩ ± (20 % of setting + 20digit) ± (10 % of setting + 10digit) –– ––
Judgement current = test voltage/(UPPER,LOWER)
[In the humidity range of 20 %rh to 70 %rh (no codensation), with no disturbance such as swinging of the test leadwire]
[In LOWER judgement, at least 0.5 s is necessary for testing after the WAIT TIME has elapsed. In LOWER judgement
for 200 nA or lower, a wait time of at least 1.0 s is necessary.]
General Specifi cations
Item TOS9200 TOS9201
Environment
Installation location Indoors at an altitude of up to 2000 m
Warranty range Temperature 5 °C to 35 °C
Humidity 20 %rh to 80 %rh (No condensation)
Operating range Temperature 0 °C to 40 °C
Humidity 20 %rh to 80 %rh (No condensation)
Storage range Temperature -20 °C to 70 °C
Humidity 90 %rh or less (No condensation)
Power requirements
Nominal voltage range (Allowable voltage range) 100 V to 120 V AC / 200 V to 240 V AC (85 V to 130 V AC / 170 V to 250 V AC) Selectable
Power consumption Using no load (READY) 100 VA or less
Using the rated load Maximum of 800 VA
Allowable frequency range 47 Hz to 63 Hz
Insulation resistance 30 M Ω or more (500 V DC) [between the AC LINE and chassis]
Hipot 1390 V AC, 2 seconds, 20 mA or less [between the AC LINE and chassis]
Ground bond 25 A AC/0.1 Ω or less
Electromagnetic compatibility (EMC) (*6) Conforms to the requirements of the following directive and standard.
EMC Directive 89/336/EEC, EN61326, EN61000-3-2, EN61000-3-3
Under following conditions
1. Used test leadwire TL01-TOS which is supplied. 2. No discharge occurs at outside of the tester.
3. Used the shielded cable which length is less than three meters when the SIGNAL I/O is used.
Safety (*6,7) Conforms to the requirements of the following directive and standard.
Low Voltage Directive 73/23/EEC , EN61010-1, Class I, Pollution degree 2
Dimensions (maximum) 430 (455) W x 132 (150) H x 370 (440) D mm
Weight Approx. 19 kg