Atec Kikusui-TOS9201 - Manual (Page 10)

13 Kikusui Electronics Corporation
TOS9200 SERIES
Hipot Tester with Insulation Resistance Test
Item TOS9200 TOS9201
Accessory
AC Power cable 1 pc.
High-voltage test lead wire TL01-TOS (1.5 m) 1 set
Interlock jumper 1 pc.
High-Voltage Danger seal 1 sheet
Fuse 1 pc.
Operation Manual Operation Manual for Tester: 1 copy, Operation for GPIB/RS-232C Interface: 1 copy
*6 Only on models that have CE marking on the panel. Not applicable to custom order models.
*7 This instrument is a Class I equipment. Be sure to ground the protective conductor terminal of the instrument. The safety of the instrument is not guaranteed unless the instrument is grounded properly.
Electrical performance
Item TOS9200 TOS9201
Maximum rating
voltage AC 5.0 kV
DC 6.0 kV
Number of channels 4 (Each channel is settable to HIGH, LOW, or OPEN.)
Maximum number of scanners connected 4 scanners,Channel numbers are determined in order of connection to the TOS9200/9201 tester.
1 st scanner CH1 to CH4 2 nd scanner CH5 to CH8 3 rd scanner CH9 to CH12 4 th scanner CH13 to CH16
Contact check function None (*1) Provided
Lamps and LEDs POWER Lights as it is interlocked with the POWER switch of the TOS9200/9201 tester
DANGER Lights as it is interlocked with the DANGER lamp of the TOS9200/9201 tester
CHANNEL Lights during a test at each channel HIGH: red; LOW: green; Under contact check: orange
Power requirements
Nominal voltage range (allowable voltage range) 100 V to 120 V AC/200 V to 240 V AC (85 V to 132 V AC/170 V to 250 V AC) Automatic switching
Power consumption In READY state Approx. 12 VA
During test 40 VA maximum
Allowable frequency range 47 Hz to 63 Hz
Insulation resistance 30 M Ω or more (500 V DC) [between the AC LINE and chassis]
Hipot 1390 V AC, 2 seconds, 10 mA or less [between the AC LINE and chassis]
Ground bond 25 A AC/0.1 Ω or less
Electromagnetic compatibility (EMC) (*2) Conforms to the requirements of the following directive and standard.
EMC Directive 89/336/EEC, EN61326, EN61000-3-2, EN61000-3-3
Under following conditions
1. Used test leadwire TL07-TOS which is supplied. 2. No discharge occurs at outside of the tester.
3. Used the shielded cable which length is less than three meters when the SIGNAL I/O is used.
Safety (*2,3) Conforms to the requirements of the following directive and standard.
Low Voltage Directive 73/23/EEC, EN61010-1, Class I, Pollution degree 2
Environment
Installation location Indoors and at altitudes up to 2000 m
Warranty range Temperature 5 °C to 35 °C
Humidity 20 %rh to 80 %rh (no condensation)
Operating range Temperature 0 °C to 40 °C
Humidity 20 %rh to 80 %rh (no condensation)
Storage range Temperature -20 °C to 70 °C
Humidity 90 %rh or less (no condensation)
Dimensions 430(435)W ✕ 88(105)H ✕ 370(415) Dmm
Weight Approx. 6.5 kg
Accessories
AC power cable 1 pc.
High-voltage test leadwires, red 4 pc. (1.5 m each) 8 pc. (1.5 m each)
High-voltage leads for parallel connection 1 set (0.5 m each)
Interface cable 1 pc.(0.5 m)
Channel-indication stickers For the panel face: 1 sheet; for the test leadwires: 1
“HIGH VOLTAGE, DANGER” stickers 2 sheets
Fuses 2 pc. (including a spare contained in the fuse holder)
Operation Manual 1 copy
*2 Only on models that have CE marking on the panel. Not applicable to custom order models.
*3 This instrument is a Class I equipment. Be sure to ground the protective conductor terminal of the instrument. The safety of the instrument is not guaranteed unless the instrument is grounded properly.
[Measurement accuracy achieved when the scanner and the TOS9220/9201 tester are connected]
In an AC hipot test, a current of approx. 22 µA/kV fl ows per scanner due to stray capacitance in the scanner in comparison with use of the TOS9220/9201 tester alone. Note that
this current may contribute to errors in current measurements conducted by the TOS9220/9201 tester.
External dimensional diagrams
MAX455
430 MAX10
MAX150
132
MAX440
370 MAX
30 430
MAX435
MAX105
88
370 MAX5
MAX415
Unit: mm