Atec Anritsu-MT2720T - Manual (Page 5)

Spectrum Master™ MS2720T Spectrum Analyzer Specifications
MS2720T TDS PN: 11410-00646 Rev. H 5 of 24
Tracking Generator (Options 809, 813, and 820)
Setup Parameters
Frequency Center/Start/Stop, Span, Signal Standard, Channel #, Frequency Step/Offset, Channel Offset
Amplitude Reference Level (RL), Scale, Attenuation Auto/Level, RL Offset, Units, Pre-Amp, Detection
Span Span, Span Up/Down (1-2-5), Full Span, Zero Span, Last Span
Bandwidth RBW, Auto RBW, VBW, Auto VBW, VBW/Average Type (Linear/Log), RBW/VBW Ratio, Span/RBW Ratio
Generator On/Off, Output Power, Mode (CW/Tracking), Settings, Transmission Measurement
Tracking Generator Settings External Gain/Loss, Power Statistics (On/Off)
Transmission Measurement Settings Normalize (Off/On), Scale, Reference Position and Amplitude, Transmission Statistics and Offset
Maximum Continuous Input +23 dBm, ± 50 VDC
Frequency Frequency Range
MS2720T-0809 100 kHz to 9 GHz
MS2720T-0813 100 kHz to 13 GHz
MS2720T-0820 100 kHz to 20 GHz
Frequency Accuracy Aging: ± 1.0 x 10 –6 per 10 years
Accuracy: ± 0.3 x 10 –6 (25 °C ± 25 °C) plus aging
Output Power
100 kHz to 20 GHz –40 dBm to 0 dBm
Step Size 0.1 dB nominal
Dynamic Range
9 GHz Instrument > 110 dB typical 100 kHz to 7 GHz
> 100 dB typical > 7 GHz to 9 GHz
13 GHz and 20 GHz Instruments > 100 dB typical 100 kHz to 12 GHz
> 80 dB typical > 12 GHz to 20 GHz
Level Accuracy (At least 30 minute warm-up after 1 hour non-operating at 15 to 35 °C ambient, excludes load VSWR effects)
VSWR
100 kHz to 5 GHz 2:1 typical
> 5 GHz to 20 GHz 4:1 typical
Interference Analyzer (Option 25)
Measurements
Spectrum Field Strength
Occupied Bandwidth
Channel Power
Adjacent Channel Power (ACPR)
AM/FM/SSB Demodulation (Wide/Narrow FM, Upper/Lower SSB), (audio out only)
Carrier-to-Interference ratio (C/I)
Spectrogram Collect data up to 72 hours
Signal Strength Gives visual and aural indication of signal strength
Received Signal Strength Indicator (RSSI) Collect data up to 72 hours
Signal ID ID up to 12 FM, GSM, W-CDMA, CDMA or Wi-Fi signals based on RF bandwidth
Interference Mapping Draw bearing of signal strength from GPS location on on-screen map
Application Options Impedance (50 Ω, 75 Ω, Other)
Compatible with the MA2700A InterferenceHunter™ Handheld Direction Finding System
Channel Scanner (Option 27)
General
Number of Channels 1 to 20 Channels (Power Levels)
Measurements Graph/Table, Max Hold (On/5 s/Off), Frequency/Channel, Current/Maximum, Dual Color
Scanner Scan Channels, Scan Frequencies, Scan Custom List, Scan Script Master™
Amplitude Reference Level, Scale
Custom Scan Signal Standard, Channel, # of Channels, Channel Step Size, Custom Scan
Frequency Range 9 kHz to 9, 13, 20, 32, or 43 GHz
Frequency Accuracy ± 10 Hz + time base error
Measurement Range –110 dBm to +30 dBm
Application Options Impedance (50 Ω, 75 Ω, Other)
Frequency Range 20 °C to 30 °C
(after 30 minute warm-up)
0 °C to 50 °C
(after 60 minute warm-up)
100 kHz to 9 GHz
> 9 GHz to 13 GHz
> 13 GHz to 18 GHz
Maximum
± 1.5 dB
± 1.6 dB
± 2.0 dB
Typical
± 0.5 dB
± 1.0 dB
± 1.0 dB
Maximum
± 2.0 dB
± 2.1 dB
± 2.5 dB
Typical
± 1.0 dB
± 1.5 dB
± 1.5 dB