Atec Anritsu-MT2720T - Manual (Page 12)

12 of 24 PN: 11410-00646 Rev. H MS2720T TDS
Spectrum Analyzer Specifications Spectrum Master™ MS2720T
LTE FDD/TDD Measurements (Option 883)
(continued)
LTE TDD Measurements
Setup Parameters
Frequency E-UTRA bands 33 - 43 (tunable 10 MHz to 4.0 GHz)
Center, Signal Standard, Channel #, Closest Channel, Decrement/Increment Channel
Bandwidth (MHz) 1.4, 3, 5, 10, 15, 20
Span (MHz) Auto, 1.4, 3, 5, 10, 15, 20, 30
Amplitude Scale/Division, Power Offset, Auto Range, Adjust Range
Sweep Single/Continuous
EVM Mode Auto, PBCH only, Max Hold
Trigger No Trigger/Ext Trigger, Rising/Falling
Save/Recall Setup, Measurement, Screen Shot (save only), to Internal/External Memory
Measurement Summary Screens Overall Measurements, RF Measurements, Modulation Measurements
LTE TDD RF Measurements
RF Channel Power Accuracy ± 1.5 dB, ± 1.0 dB typical, (RF input –30 dBm to +10 dBm)
LTE TDD Modulation Measurements
RS Power Accuracy ± 1.0 dB typical, (RF input –50 dBm to +10 dBm)
Frequency Error ± 10 Hz + time base error, 99 % confidence level
Residual EVM (rms) 2.0 % typical (E-UTRA Test Model 3.1, RF Input –30 dBm to +10 dBm)
Over-the-Air (OTA) Measurements
Scanner Six strongest signals if present
Auto Save – Sync Signal power and Modulation Results with GPS information
Tx Test Scanner – Three strongest signals if present
RS Power – Strongest signal
Mapping Map On-screen S-SS, RSRP, RSRQ, or SINR of Cell ID with strongest signal
Scanner – three strongest signals if present
Save and Export Mapping data: *.kml, *.mtd (tab delimited)
RF Modulation Over-the-Air (OTA) Pass/Fail
Channel Spectrum
Channel Power
Occupied Bandwidth
Power vs. Time
Frame View
Sub-Frame View
Total Frame Power
DwPTS Power
Transmit Off Power
Cell ID
Timing Error
ACLR
Spectral Emission Mask
Category A or B (Opt 1)
RF Summary
Power vs. Resource Block (RB)
RB Power (PDSCH)
Active RBs, Utilization %
Channel Power, Cell ID
Constellation
QPSK, 16 QAM, 64 QAM
Modulation Results
Ref Signal Power (RS)
Sync Signal Power (SS)
EVM – rms, peak, max hold
Frequency Error – Hz, ppm
Carrier Frequency
Cell ID
Control Channel Power
Bar Graph or Table View
RS, P-SS, S-SS
PBCH, PCFICH
Total Power (Table View)
Modulation Results
Antenna Icons
Detects active antennas (1 or 2)
Modulation Summary
Scanner
Cell ID (Group, Sector)
S-SS, RSRP, RSRQ, SINR
Dominance
Modulation Results – On/Off
Tx Test
Scanner
RS Power of MIMO antennas
Cell ID, Average Power
Delta Power (Max-Min)
Graph of Antenna Power
Modulation Results – On/Off
Mapping
On-screen
S-SS, RSRP, RSRQ, or SINR
Scanner
Modulation Results – Off
View Pass/Fail Limits
All, RF, Modulation
Available Measurements
Channel Power
Occupied Bandwidth
ACLR
Frequency Error
Carrier Frequency
Dominance
EVM peak, rms
RS Power
SS, P-SS, S-SS Power
PBCH Power
PCFICH Power
Cell, Group, Sector ID
Frame Power
DWPTS Power
Transmit Off Power
Timing Error