Atec Anritsu-MT2720T - Manual (Page 4)

4 of 24 PN: 11410-00646 Rev. H MS2720T TDS
Spectrum Analyzer Specifications Spectrum Master™ MS2720T
Spectrum Analyzer
(continued)
Third-Order Intercept (TOI) (–20 dBm tones 100 kHz apart, 0 dB Attenuation Preamp OFF)
2.4 GHz +14 dBm minimum
50 MHz to 20 GHz +20 dBm typical
> 20 GHz to 32 GHz +15 dBm typical
> 32 GHz to 43 GHz +20 dBm typical
P1dB
< 4 GHz 5 dBm typical
4 GHz to 20 GHz 12 dBm typical
> 20 GHz to 32 GHz 7 dBm typical
> 32 GHz to 43 GHz 12 dBm typical
Second Harmonic Distortion (0 dB input attenuation, –30 dBm input)
50 MHz –54 dBc maximum
VSWR (> 10 dB input attenuation)
9 GHz Instruments
< 4 GHz 1.5:1 typical
4 GHz to 8 GHz 1.8:1 typical
13 GHz to 43 GHz Instruments
< 20 GHz 1.5:1 typical
20 GHz to 43 GHz 2.0:1 typical
Internal Atomic Clock (Option 1)
Frequency Accuracy 1 x 10 -9 + aging
Aging Rate 1 x 10 -9 per year
Initial Warmup 10 minutes to meet the accuracy specification
High Accuracy Power Meter (Option 19)
(Requires external USB Power Sensor)
Amplitude Maximum, Minimum, Offset, Relative On/Off, Units, Auto Scale
Average # of Running Averages, Max Hold
Zero/Cal Zero On/Off, Cal Factor (Center Frequency, Signal Standard)
Limits Limit On/Off, Limit Upper/Lower
Power Sensor Model PSN50 MA24105A MA24106A MA24108A/18A/26A
Description High Accuracy
RF Power Sensor
Inline High
Power Sensor
High Accuracy
RF Power Sensor
Microwave USB
Power Sensor
Frequency Range 50 MHz to 6 GHz 350 MHz to 4 GHz 50 MHz to 6 GHz 10 MHz to 8/18/26 GHz
Connector Type N(m), 50 Ω Type N(f), 50 Ω Type N(m), 50 Ω Type N(m), 50 Ω
(8/18 GHz)
Type K(m), 50 Ω
(26 GHz)
Dynamic Range –30 dBm to +20 dBm
(0.001 mW to 100 mW)
+3 dBm to +51.76 dBm
(2 mW to 150 W)
–40 dBm to +23 dBm
(0.1 µW to 200 mW)
–40 dBm to +20 dBm
(0.1 µW to 100 mW)
VBW 100 Hz 100 Hz 100 Hz 50 kHz
Measurand True-RMS True-RMS True-RMS True-RMS, Slot Power,
Burst Average Power
Measurement Uncertainty ± 0.16 dB 1 ± 0.17 dB 2 ± 0.16 dB 1 ± 0.18 dB 3
Data sheet
(for complete specifications)
11410-00414 11410-00621 11410-00424 11410-00504
Notes: 1. Total RSS measurement uncertainty (0 ºC to 50 ºC) for power measurements of a CW signal greater than –20 dBm with
zero mismatch errors.
2. Expanded uncertainty with K=2 for power measurements of a CW signal greater than +20 dBm with a matched load.
Measurement results referenced to the input side of the sensor.
3. Expanded uncertainty with K=2 for power measurements of a CW signal greater than –20 dBm with zero mismatch
errors.