Atec Agilent-E5052A - Manual (Page 8)

8
Port Output (DC Power/Control)
Table 1-21. DC power voltage output
Description Specifications
Voltage range 0 to 16 V
Resolution 1 mV
Setting accuracy ± (0.2% + 2 mV)
Maximum output current 80 mA
Noise < 10 nV / Hz at 10 kHz
Output resistance < 0.3 ohm (typical)
Settling time @error: 0.1% < 20 msec (typical)
Table 1-22. DC control voltage output
Description Specifications
Voltage range
-15 to 35 V
Resolution 0.1 mV
Setting accuracy
-15 to 0 V ± ((Setting + 15 V) x 0.1% + 5 mV)
(typical)
0 to 35 V ± (Setting x 0.1% + 2 mV) (typical)
Maximum output current 20 mA (typical)
Noise
0 to 20 V
1 nV / Hz at 10 kHz
-15 to 0 V, 20 to 35 V 1.5 nV / Hz at 10 kHz
Output resistance (DC) < 50 ohm
Output resistance (AC) 50 ohm (nominal)
Settling time @error: 0.1% < 20 msec (typical)
Test Port Input
Table 1-23. RF in
Description Specifications
Input level
10 M to 30 MHz -15 to +20 dBm
30 M to 7 GHz -20 to +20 dBm
Input attenuator 0 to 35 dB in 5 dB steps
Damage level +23 dBm (nominal)
VSWR
10 M to 30 MHz < 1.6
30 M to 2 GHz < 1.2
2 G to 3 GHz < 1.3
3 G to 4 GHz < 1.3 (typical)
4 G to 7 GHz < 1.5 (typical)
General Information
Table 1-24. Front panel information
Description
Supplemental information
RF in
Type
Type-N, female, 50 ohm (nominal)
DC power / control
Type
BNC, female, 50 ohm (nominal)
Display
Size
10.4 in TFT color LCD
Resolution VGA (640 • 480) 1
Table 1-25. Rear panel information
Description
Supplemental information
External trigger connector
Type BNC,
female
Input level Low threshold voltage: 0.5 V
High threshold voltage: 2.1 V
Input level range: 0 to + 5 V
Pulse width
≥ 2 µsec, typical
Polarity Positive/negative selectable
External trigger 0 to 1 usec
timing adjustment
External reference signal input connector
Type BNC,
female
Input frequency 10 MHz ± 10 Hz, typical
Input level -6 dBm to + 16 dBm, typical
Internal reference signal output connector
Type BNC,
female
Input frequency 10 MHz ± 50 Hz, typical
Signal type Sine wave, typical
Output level 2.5 dBm ± 3 dB, typical
Output impedance 50 ohm nominal
VGA video output 15-pin mini D-Sub; female;
drives VGA compatible monitors
GPIB 24-pin D-Sub (type D-24), female;
compatible with IEEE-488
Parallel port 36-pin D-Sub (type 1284-C), female;
provides connection to printers
USB port
Universal serial bus jack
Type A configuration, female;
provides connection to printer, USB/GPIB
interface
Type B configuration
2 (USBTMC), female;
provides connections to an external PC
Contact 1 Vcc: 4.75 to 5.25 VDC, 500 mA, maximum
Contact 2 Data
Contact 3 +Data
Contact 4 Ground
LAN 10 / 100 base T ethernet, 8-pin configuration;
auto selects between the two data rates
24 Bit I/O port 36-pin D-sub, female; provides connection to
handler system
Line power 3
Frequency 47 Hz to 63 Hz
Voltage 90 to 132 VAC, or 198 to 264 VAC
(automatically switched)
VA maximum 500 VA max
1. Valid pixels are 99.99% and more. Below 0.01% (approx. 30 points) of fixed points
of black, blue, green or red are not regarded as failure.
2. USB Test and Measurement Class (TMC) interface that communicates over USB
using USBTMC messages based on the IEEE 488.1 and IEEE 488.2 standards.
Type B configuration will be included with E5052A shipments beginning August 2005.
3. A third-wire ground is required.
√
√
√