Atec Agilent-34972A - Manual (Page 20)

20
Modules specifi cations
The Agilent 34970A/34972A accuracy specifications already
include the switching offset and reference junction errors
shown below. These errors are listed separately for deter-
mining system error with external measurement devices.
Up to three modules, in any combination, can be inserted
into a single mainframe. The 34970A/34972A’s internal
DMM connections are accessible only through the 34901A,
34902A, and 34908A low-frequency multiplexers.
On-module screw terminals accept wire sizes from
16 gage to 22 gage. Twenty-gage wire is recommended for
high channel count applications. The 34905A and 34906A
RF Multiplexers use SMB connectors. A standard set of
(10) BNC-to-SMB adapter cables is provided with each
RF module for convenient BNC connections.
Multiplexer Actuator Matrix RF multiplexer Multifunction
34901A 34902A [1] 34908A 34903A 34904A 34905A 34906A 34907A
General
Number of channels 20 + 2 16 40 20 4 x 8 Dual 1 x 4 See page 25
for module
specifi cations
2/4 wire 2/4 wire 1 wire SPDT 2 wire 50 Ω 75 Ω
Connects to internal DMM ● ● ●
Scanning speed 60 ch/s 250 ch/s [1] 60 ch/s
Open/close speed 120/s 120/s 70/s 120/s 120/s 60/s
Input
Voltage (dc , ac rms) [2] 300 V 300 V 300 V 300 V 300 V 42 V
Current (dc , ac rms) 1 A 50 mA 1 A 1 A 1 A 0.7 A
Power (W , VA) 50 W 2 W 50 W 50 W 50 W 20 W
DC characteristics
Offset voltage [3] < 3 uV < 6 uV < 3 uV < 3 uV < 3 uV < 6 uV
Initial closed channel R [3] < 1 Ω < 1 Ω < 1 Ω < 0.2 Ω < 1 Ω < 0.5 Ω
Isolation ch-ch, ch-earth > 10 GΩ > 10 GΩ > 10 GΩ > 10 GΩ > 10 GΩ > 1 GΩ
AC characteristics
Bandwidth [4] 10 MHz 10 MHz 10 MHz 10 MHz 10 MHz 2 GHz [5] 2 GHz [5]
Insertion loss (dB) 10 MHz — — — — — -0.1 -0.1
100 MHz — — — — — -0.4 -0.4
500 MHz — — — — — -0.6 -0.5
1 GHz — — — — — -1 -1
1.5 GHz — — — — — -1.2 -1.5
2 GHz — — — — — -3 -2
SWR 0-9.99 MHz — — — — — 1.02 1.02
10-99.99 MHz — — — — — 1.05 1.05
100-499.99 MHz — — — — — 1.20 1.25
500-999.99 MHz — — — — — 1.20 1.40
1-1.499 GHz — — — — — 1.30 1.40
1.5-2 GHz — — — — — 1.40 2.00
ch-ch cross talk (dB) [4] 10MHz -45 -45 -18 [6] -45 -33 -100 -85
100 MHz — — — — — -85 -75
500 MHz — — — — — -65 -65
1 GHz — — — — — -55 -50
1.5 GHz — — — — — -45 -40
2 GHz — — — — — -35 -35
Risetime < 300 ps
Signal delay < 3 ns
Capacitance HI - LO < 50 pF < 50 pF < 50 pF < 10 pF < 50 pF < 20 pF
LO - Earth < 80 pF < 80 pF < 80 pF < 80 pF < 80 pF —
Volt-Hertz limit 10 8 10 8 10 8 10 8 10 8 10 10
Other
T/C cold junction accuracy [3]
(typical) 0.8 °C 0.8 °C 0.8 °C [8]
Switch life No load (typical) 100 M 100 M 100 M 100 M 100 M 5 M 5 M
Rated load (typical) [7] 100 k 100 k 100 k 100 k 100 k 100 k 100 k
Temperature Operating all cards — 0 °C to 55 °C
Storage all cards — -20 °C to 70 °C
Humidity (non-condensing) all cards — 40 °C to 80% RH
[1] Not recommended for connection to ac line without external tran-
sient suppression. Up to 250 ch/s to internal memory. See scanning
rates for measurement condition and rate on each instrument.
[2] Channel-to-channel or channel-to-earth
[3] Errors included in DMM measurement accuracy specifi cations
[4] 50 Ω source, 50 Ω load
[5] Bandwidth direct to card SMB connectors
[6] Isolation within channel 1 to 20 or 21 to 40 banks is -40 dB
[7] Applies to resistive loads only
[8] Thermocouple measurements not recommended with 34908A
module due to common lo confi guration