Franklin Fueling Systems Tank Sentinel Quick Reference Guide - Manual (Page 2)

Tank Sentinel ®
Quick Reference Guide
INCON® and Tank Sentinel®
are registered trademarks of
INTELLIGENT CONTROLS INC • PO BOX 638 • SACO ME 04072
Special Keys ( Continued from other side )
Menu Select Keys ( M1 — M4 )
are under the display. Press to make a choice or
to enter menus (example uses: to print reports,
view alarm lists, or to show leak test status).
When inputting data, such as a password, the
M1 key can be used to move the cursor left, M2
to move the cursor right, and M4 to back-
space over ( delete ) a character.
Alarm Annunciator & Alarm Status Row
Green light – on when power is on
Yellow light – on with System WARNING alarms
...flashes when alarms are new / not acknowledged
Red light – on with Tank, Sensor, & Line ALARMS
...flashes when alarms are new / not acknowledged
Warning or Alarm lights turn off when cleared
alarms are acknowledged and removed from the
alarm list ( unless an alarm is still active ).
The Report Printer is activated / prints on alarm.
Alarms may be programmed to sound the solid-
tone or beeping Annunciator Alarm Horn. But,
regardless of how the programming was done,
the alarm status row lights will always flash
when a new warning or alarm exists. Pay close
attention to the Alarm Status lights!
TO SILENCE THE ALARM HORN
the ACK SHIFT key ...if the console
requires a password, the display will
read: ENTER PASSWORD: ( input
the code and press
ENTER ).
TO VIEW AN ALARM LIST
– under WARNING or ALARM messages (see
example display at right). Use the
UP / DOWN
keys to show alarms in the alarm list until all
alarms have been viewed ( Active, Cleared or
Transient alarms can be in the alarm list ).
TO REMOVE CLEARED ALARMS FROM
THE ALARM LIST
View an Alarm List ( see above ) and press the
ACK SHIFT key to remove Cleared alarms. The
display will show OKAY and the Alarm status row
lights go out if no alarms exist ( see Note 1 ).
A
service call may be required to clear an Active
Alarm.
TO START A LEAK TEST except TS-504/508
TEST then M2 and a menu select
key ( M1 — M4 ) under the type of
test you want to start (0.1 gph or 0.2
gph tank or line test).
Select a tank or line number by using ( M1 — M4 )
keys... use DOWN key to see other tank or line numbers
that you may choose from.
TO CANCEL / ABORT A LEAK TEST
Press TEST then M3 and a menu select key
( M1 — M4 ) under the type of test you want to
abort.
TO SHOW LEAK TEST STATUS
Press TEST then M1 ...use the DOWN key to
view the status of other tank or line leak tests.
TO ENTER THE SETUP MODE
MENU then the M1 key. If the
console requires a password (highly
recommended), the display will read:
ENTER PASSWORD: (input the code and press ENTER )
See the Operator’s Guide about Language and Upgrade
menu choices (Data Log is for diagnostic use only).
TO PRINT or FAX A REPORT
REPORT and then the DOWN key
to view report types. Press
M1 — M4 to make a choice.
Press M1 to send the report to the printer, or press M2
to send the report to a remote FAX machine. The
FAX / Modem hardware is an optional extra cost item.
Key Strokes to Print a (tank) Leak Estimate
Report:
REPORT M4 M1 M1 – M4 / DOWN
1 2 3 4 / 5 – See other side and the Operator’s Guide –
NOTE
# 1
A A A A AC C C C C K K K K K
SHIFT
J W
R R R R RE E E E EP P P P PO O O O OR R R R RT T T T T
9
L Y
T E T E T E T E T E S S S S S T T T T T
0
H U
M M M M M E E E E E N N N N N U U U U U
7
NOTE
# 2
M1
LEFT
M2
RIGHT
M3 M4 OR OR OR
Press a
menu
select
key –
SYSTEM TANK SENSOR LINE
WARNING TESTING ALARM OKAY
CANCEL
D Q
TAN K
4
F S
WATE R
6
G T
UP
+ / –
K X
DOWN
SPACE
ENTE R
M Z
CHECK
.
L Y
TEST
0
AC K
SHIFT
H U
MENU
7
I V
ALAR M
8
J W
REPORT
9
A N
PRODUCT
1
C P
LEVEL
3
B O
GROSS
2
E R
ULLAGE
5
M1
LEFT
M2
RIGHT
M3 M4
POWER
ALARM
TEST
WARNING ALARM
Call
Number(s):
Press
Press
Press
Press