Derale Performance Low Profile Thermostatic Sandwich Adapter with 3__8" NPT Ports and 3__4-16 Filter Thread" - Manual

25730-25734-25770-27774-InstructionSheet
Derale Performance, Los Angeles, CA 800.421.6288 www.derale.com
INSTALLATION INSTRUCTIONS
ENGINE SANDWICH ADAPTER KIT
PART # 25730-25734 & 25770-25774
Please read these instructions completely
before beginning installation
KIT CONTENTS
QTY. DESCRIPTION
1 Sandwich Adapter
1 O-ring
1 Sleeve Nut
IMPORTANT
In most cases the Factory Oil Filter will work with the
supplied sandwich adapter. In some applications where
the frame or exhaust system interferes with the new
filter depth we recommend using a shorter filter length.
See the chart below for possible filter options.
SLEEVE NUT
Colored Label
FRAM WIX FRAM WIX
THREAD LABEL FILTER FRAM FILTER WIX FILTER FRAM FILTER WIX
SIZE COLOR HEIGHT P/N HEIGHT P/N HEIGHT P/N HEIGHT P/N
3/4-16 YELLOW
13/16-16 BLUE/RED
18mm x 1.5 WHITE
20mm x 1.5 BLACK
22mm x 1.5 GREEN
4.92 PH3600 4.83 51516 3.34 PH3614 3.4 51348
4.94 PH3429 4.83 51045 3.36 Ph3506 3.4 51042
4.94 PH3980 4.83 51036 3.36 PH3387A 3.4 51040
3.47 PH7317 N/A N/A 3.39 PH3593A 3.14 51381
4.94 PH3750 4.57 57026 3.98 PH2 3.43 57060
Diagram #1
VERIFYING SLEEVE NUT THREAD SIZE
SANDWICH ADAPTER INSTALLATION
Included in this kit should be a sleeve nut with thread specification as indicated
by the part number purchased and the product packaging. The thread size can
be verified by screwing the male end of the Sleeve Nut into the new or old engine
oil filter. If it is incorrect, please contact your dealer.
The Sandwich Adapter fits between the oil filter and the engine block. Before
removing the oil filter, check the clearance between the bottom of the filter and
the closest vehicle obstruction. If there are none, then proceed with the
installation. If you determine that the stock filter will not fit, refer to the Filter Chart
for alternative filter heights.
1.
Remove the factory oil filter from the vehicle.
2. Remove the colored label from the Sleeve Nut (If there is one).
3. Take the Sandwich Adapter and two Hose Barb Fittings (Not Provided).
Using Teflon Tape or a suitable sealant, screw the Hose Barb Fittings
clockwise into the Sandwich Adapter until snug. (See Diagram #2)
4. Using a wrench tighten the two Hose Barb Fittings.
5. Take the O-ring provided, apply a thin film of oil and install into the O-ring
groove on the Sandwich Adapter. (See Diagram #2)
Diagram #2
6. Making sure the engine block filter landing is clean from oil and dirt, take the Sleeve Nut, Sandwich Adapter, O-ring, and
install onto engine sliding the Sleeve Nut thru the Sandwich Adapter. Turn sleeve nut clockwise onto the engines filter
nipple. (See Diagram #2)
7. Using a torque wrench, torque the Sleeve Nut to 20 ft. lbs.
1. Install both ends of the hose onto the Hose Barb Fittings, forming a loop.
2. Take the looped end and route the hose to the oil cooler making sure to stay clear of sharp objects, exhaust systems, etc.
All bends in hose need to have a minimum radius of 5” or the diameter of a small coffee can.
3. Cut and attach hoses to the oil cooler. Secure hoses using zip ties.
1. Before starting the vehicle, check engine oil level and add accordingly.
2. Always check fluid levels on a flat surface.
3. After installation and vehicle has completely warmed up, recheck fluid level and inspect all connections for leaks.
ROUTING HOSES (HOSE SOLD SEPARATELY)
SYSTEM CHECK
Note:
Warning: Installation of accessories should only be undertaken by those with mechanical knowledge and are familiar with working on
vehicles. Always use eye protection (goggles, safety glasses or shield). Park the vehicle in a well lit area, on level ground and apply the
parking brake. Only work on a cold vehicle that has been sitting overnight, failure to do so will result in severe burns and injury. Before starting
the vehicle, make sure no tools or any other items are left under hood that could interfere with or be drawn into moving parts of the engine.
Failure to follow instructions can lead to severe damage and personal injury.