Derale Performance Single Mount 3__8" NPT Ports Up Remote Transmission Filter Kit, Premium - Manual

Diagram #1
13091-InstructionSheet Rev-2-2-2011
Derale Performance, Los Angeles, CA 800.421.6288 www.derale.com
INSTALLATION INSTRUCTIONS
AUTOMATIC TRANSMISSION FILTER KIT W/ GAUGE
PART # 13091
Please read these instructions completely before starting the installation.
KIT CONTENTS
QTY. DESCRIPTION
1 Filter Mount
1 Oil Filter
1 Temperature Gauge
1 Gauge mounting Bezel
1 Gauge mounting Bracket
3 #14 Sheet Metal Screws
4ft 11/32” OEM Spec Hose
2 3/8” NPT x 3/8” Barb Fittings
TOOLS NEEDED
QTY. DESCRIPTION
1 Insta-dapt Adapter
4 Hose Clamp
1 3/4-16 Filter Nipple
2 10-32 Mounting Nuts & Washers
1 10-32 Temp Sender Nut & Washer
3 6-32 Mounting Nuts & Washers
1 Temp Sender
INSTALLATION
Filter Mount
Locate Transmission Lines
Hose Connections
Note:
Warning:
Important:
Note:
1. Choose a convenient location for the Filter Mount, making sure there is
enough space for future servicing of the oil filter.
Suggested Locations: Firewall, Radiator Support, Fender well
2. Take the 3/4-16 Filter Nipple supplied and install onto the Filter Mount, making
sure the shorter end of threads is towards the Filter Mount. (See Diagram #1)
3. Using the filter mount as a template, mark and drill three 3/16” holes.
4. Using the #14 Sheet Metal Screws provided, install the Filter Mount onto
the vehicle.
5. Identify the
6. Apply a light coat of oil onto the o-ring of the oil filter and install on the
filter mount.
1. Find the two transmission oil lines that run from the transmission to the
radiator, usually steel lines connected to the bottom radiator tank or on a
cross-flow radiator the passenger side tank.
2. Determine the supply line to the transmission. Warm up vehicle & feel the
trans lines, the warmer of the two lines will be the supply line.
1. Disconnect the supply transmission cooler line from the radiator.
2. Take the supplied Insta-dapt Adapter fitting and install onto radiator using the
appropriate Male or Female end. (See Diagram #2)
The Insta-dapt fitting has a 1/2”-20 Thread and fits most vehicles with
5/16” transmission cooler lines. For vehicles that are not compatible with the
Insta-dapt Adapter, please reference the Radiator Adapter Fitting Guide or go
to www.derale.com for alternative radiator fitting options.
3. Using the supplied Hose and Hose Clamps, Connect both ends of the Hose
to the 3/8” NPT x 3/8” Barb Fittings now installed on the Filter Mount forming
a loop.
4. Carefully route the looped Hose to the desired locations.
5. Cut and attach the Hose coming from the IN on the Filter Mount to the supply
line coming from the Transmission. (See Diagram #3)
6. Cut and attach the Hose coming from the OUT on the Filter Mount to the Insta-
dapt Adapter now attached to the Radiator. (See Diagram #3)
When routing hoses, be sure to keep all hoses away from sharp edges,
moving parts and hot engine components. Hoses should be routed
carefully and should not be bent in less than a 3” radius.
A kinked hose will restrict flow and could cause transmission failure.
Filter element should be replaced every 25,000 miles or whenever the
transmission is serviced. Order Derale replacement filer element part #13092.
3/8” NPT x 3/8” Barb Fittings, using Teflon Tape or suitable Sealant
install the two 3/8” NPT x 3/8” Barb Fittings onto the Filter Mount.
Standard Screw Driver
or 5/16” Nut Driver
Razor Knife
6mm Nut Driver
8mm Nut Driver
5/8” Open End Wrench
3/4” Open End Wrench
12mm Open End Wrench
Center Punch
3/16” Drill Bit
Drill
Teflon Tape
Marker
Diagram #2
Insta-dapt
Adapter
Oil Filter
3/4-16 Filter Nipple
Short End Screws
into Filter Mount
Filter Mount
Trans.
Insta-dapt
Adapter
Radiator
Diagram #3
Oil Filter
Filter Mount
(Continues on Page 2)
Temp Sender
Port