beautypg.com

Derale Performance Engine Oil Filter Relocation Kit, 1_2" NPT Ports with 20x1.5mm Engine Thread Size User Manual

Diagram #2, Diagram #1

background image

15715-15717-15718-15725-InstructionSheet

INSTALLATION INSTRUCTIONS

OIL FILTER RELOCATION KIT

PART # 15715, 15717, 15718 & 15725

Derale Performance, Los Angeles, CA

800.421.6288 www.derale.com

Please read these instructions completely before beginning installation

PRE-INSTALLATION

INSTALLATION

1.

Remove the factory oil filter and clean the oil filter landing surface

on the engine block.

2.

Take the four 1/2” NPT x 1/2” Hose Barbs supplied. Using a Teflon

Tape or suitable sealant, install two 1/2” NPT x 1/2” Hose Barbs
onto the Spin-On Adapter. Install the remaining two 1/2” NPT x
1/2” Hose Barbs onto the Ports-Up Filter Mount.

1.

Apply a light coat of oil onto the O-ring.

2.

Take the O-ring and install into the groove on the Spin-On

Adapter.

3.

Install onto the engine. (See Diagram #2)

4.

Hand Tighten with the same force used in tightening a factory oil

filter.

5.

Choose a convenient location for the Ports-Up Filter Mount. Make

sure there is enough space for future servicing of the oil filter.
Suggested Locations: Firewall, Radiator Support, Fender well

6.

Take the 3/4-16 Filter Nipple supplied, making sure the shorter

end of threads is installed onto the Ports-Up Filter Mount.

7.

Using the filter mount as a template, mark and drill three 3/16”

holes.

8.

Using the #14 Sheet Metal Screws provided, install the Ports-Up

Filter Mount onto the vehicle.

9.

Using the Hose Clamps provided, attach both ends of the 1/2”

Hose provided to the hose barbs on the installed Spin-On Adapter
forming a loop.

10. Carefully route hose over to the Ports-Up Filter Mount.

Keep hoses away from sharp edges, moving parts and

Spin-On Adapter

Filter Mount

Note:

3.

Take the Hex Sleeve Nut and slide it into the Spin-on Adapters

hex feature. Sleeve Nut will only install correctly in one direction.
(See Diagram #1)

4. Take the supplied Snap Ring and carefully install into the snap ring

groove of the casting making sure it is securely fastened.
(See Diagram #1)

(See Diagram #3 on page 2)

TOOLS NEEDED

7/8” Open End Wrench
Standard Screw Driver
Drill
3/16” Drill Bit
Teflon Tape

KIT CONTENTS

QTY. DESCRIPTION

1

Spin-On Adapter

1

Ports Up Filter Mount

1

O-ring (Spin-On Adapter)

1

3/4-16 Filter Nipple

1

Hex Sleeve Nut

QTY. DESCRIPTION

1

Snap Ring

10ft.

1/2” Hose

4

1/2” NPT x 1/2” Hose Barb

4

Hose Clamps

3

#14 Sheet Metal Screws

Snap

Ring

Hex Sleeve

Nut

Snap Ring

Groove

Hose

Clamp

1/2” Hose

1/2” NPT x 1/2”

Hose Barb

Spin-On

Adapter

Spin-On

Adapter

O-ring

Diagram #2

PART #

THREAD SIZE

15715
15717
15718
15725

3/4”-16

18mm x 1.5
20
22

mm x 1.5
mm x 1.5

(Continues on Page 2)

Diagram #1

IMPORTANT

The new Filter Mount is designed to accept a 3/4-16 oil filter
(Typical Ford filter) Use Derale Part # 13092 or reference chart
on reverse for manufacturers part numbers.