Rainbow Electronics MAX7030 - Manual (Page 11)

MAX7030
Low-Cost, 315MHz, 345MHz, and 433.92MHz
ASK Transceiver with Fractional-N PLL
______________________________________________________________________________________ 11
Pin Description
PIN NAME FUNCTION
1 PAV DD
Power-Amplifier Supply Voltage. Bypass to GND with 0.01µF and 220pF capacitors placed as close
to the pin as possible.
2 ROUT
Envelope-Shaping Output. ROUT controls the power-amplifier envelope’s rise and fall times. Connect
ROUT to the PA pullup inductor or optional power-adjust resistor. Bypass the inductor to GND as
close to the inductor as possible with 680pF and 220pF capacitors, as shown in the Typical
Application Circuit.
3 TX/RX1
Transmit/Receive Switch Throw. Drive T/R high to short TX/RX1 to TX/RX2. Drive T/R low to disconnect
TX/RX1 from TX/RX2. Functionally identical to TX/RX2.
4 TX/RX2 Transmit/Receive Switch Pole. Typically connected to ground. See the Typical Application Circuit.
5 PAOUT
Power-Amplifier Output. Requires a pullup inductor to the supply voltage (or ROUT if envelope
shaping is desired), which can be part of the output-matching network to an antenna.
6 AV DD
Analog Power-Supply Voltage. AV DD is connected to an on-chip +3.0V regulator in 5V operation.
Bypass AV DD to GND with a 0.1µF and 220pF capacitor placed as close to the pin as possible.
7 LNAIN Low-Noise Amplifier Input. Must be AC-coupled.
8 LNASRC
Low-Noise Amplifier Source for External Inductive Degeneration. Connect an inductor to GND to set
the LNA input impedance.
9 LNAOUT
Low-Noise Amplifier Output. Must be connected to AV DD through a parallel LC tank filter. AC-couple
to MIXIN+.
10 MIXIN+ Noninverting Mixer Input. Must be AC-coupled to the LNA output.
11 MIXIN- Inverting Mixer Input. Bypass to AV
DD
with a capacitor as close to the LNA LC tank filter as possible.
12 MIXOUT 330 Ω Mixer Output. Connect to the input of the 10.7MHz filter.
13 IFIN- Inverting 330 Ω IF Limiter-Amplifier Input. Bypass to GND with a capacitor.
14 IFIN+ Noninverting 330 Ω IF Limiter-Amplifier Input. Connect to the output of the 10.7MHz IF filter.
15 PDMIN Minimum-Level Peak Detector for Demodulator Output
16 PDMAX Maximum-Level Peak Detector for Demodulator Output
17 DS- Inverting Data Slicer Input
18 DS+ Noninverting Data Slicer Input
19 OP+ Noninverting Op-Amp Input for the Sallen-Key Data Filter
20 DF Data-Filter Feedback Node. Input for the feedback capacitor of the Sallen-Key data filter.
21, 25 N.C. No Connection. Do not connect to this pin.
22 T/R
Transmit/Receive. Drive high to put the device in transmit mode. Drive low or leave unconnected to
put the device in receive mode. It is internally pulled down.
23 ENABLE
Enable. Drive high for normal operation. Drive low or leave unconnected to put the device into shut-
down mode.
24 DATA Receiver Data Output/Transmitter Data Input
26 DV DD
Digital Power-Supply Voltage. Bypass to GND with a 0.01µF and 220pF capacitor placed as close to
the pin as possible.
27 HV IN
High-Voltage Supply Input. For 3V operation, connect HV IN to AV DD , DV DD , and PAV DD . For 5V
operation, connect only HV IN to 5V. Bypass HV IN to GND with a 0.01µF and 220pF capacitor placed
as close to the pin as possible.