Milton CAT 966H - Manual (Page 22)

22 966H Wheel Loader specifications
Operating Specifications
Material Handling Buckets
Teeth and Bolt-On Teeth and Bolt-On
Bucket Teeth Segments Edges Teeth Segments Edges
Rated Bucket Capacity (§) m 3 3.65 3.80 3.80 3.80 4.00 4.00
yd 3 4.75 5.00 5.00 5.00 5.25 5.25
Struck Capacity (§) m 3 3.08 3.22 3.22 3.31 3.46 3.46
yd 3 4.02 4.21 4.21 4.33 4.52 4.52
Width (§) mm 3306 3306 3220 3306 3306 3220
ft/in 10'10" 10'10" 10'7" 10'10" 10'10" 10'7"
Dump Clearance at Full Lift mm 2920 2920 3083 2878 2878 3041
and 45º Discharge (§) ft/in 9'7" 9'7" 10'1" 9'5" 9'5" 10'0"
Reach at Full Lift mm 1254 1254 1127 1297 1297 1170
and 45º Discharge (§) ft/in 4'1" 4'1" 3'8" 4'3" 4'3" 3'10"
Reach with Lift Arm Horizontal mm 2847 2847 2642 2907 2907 2702
and Bucket Level (§) ft/in 9'4" 9'4" 8'8" 9'6" 9'6" 8'10"
Digging Depth (§) mm 78 108 108 78 108 108
in 3.07 4.25 4.25 3.07 4.25 4.25
Overall Length mm 8985 8985 8760 9045 9045 8820
ft/in 29'6" 29'6" 28'9" 29'8" 29'8" 28'11"
Overall Height with Bucket mm 5748 5748 5748 5803 5803 5803
at Full Raise ft/in 18'10" 18'10" 18'10" 19'0" 19'0" 19'0"
Loader Clearance Circle with mm 14 875 14 875 14 672 14 906 14 906 14 702
Bucket in Carry Position (§) ft/in 48'10" 48'10" 48'2" 48'11" 48'11" 48'3"
Static Tipping Load Straight * kg 17 519 17 124 17 336 17 366 16 974 17 186
lb 38,629 37,758 38,226 38,292 37,428 37,895
Static Tipping Load kg 15 598 15 220 15 431 15 452 15 077 15 289
Full 37º Turn lb 34,394 33,560 34,025 34,072 33,245 33,712
Breakout Force ** (§) kN 217 201 203 206 191 193
lb 48,825 45,225 45,675 46,350 42,975 43,425
Operating Weight * (§) kg 23 599 23 790 23 623 23 670 23 861 23 694
lb 52,036 52,457 52,089 52,192 52,614 52,245
(§) Specifications and ratings conform to all applicable standards recommended by the Society of Automotive Engineers, including SAE Standard J732C
governing loader ratings.
* Static tipping loads and operating weights shown are based on standard machine configuration with 26.5R25 L-4 Firestone tires, roading fenders. powertrain
guard, full fuel tank, coolants, lubricants, air conditioner and operator.
** Measured 102 mm (4.0") behind tip of cutting edge with bucket hinge pin as pivot point in accordance with SAE J732C.