Milton CAT 966H User Manual
Page 21
21
966H Wheel Loader specifications
General Purpose Buckets
Teeth and
Bolt-On
Teeth and
Bolt-On
Bucket
Teeth
Segments
Edges
Teeth
Segments
Edges
Rated Bucket Capacity (§)
m
3
3.80 4.00 4.00 4.00 4.25 4.25
yd
3
5.00 5.25 5.25 5.25 5.50 5.50
Struck Capacity (§)
m
3
3.28 3.43 3.43 3.43 3.62 3.62
yd
3
4.29 4.48 4.48 4.48 4.73 4.73
Width (§)
mm
3145
3145
3059
3306
3306
3220
ft/in
10'4" 10'4" 10'0" 10'10" 10'10" 10'7"
Dump
Clearance
at
Full
Lift
mm
2934 2934 3086 2934 2934 3086
and 45º Discharge (§)
ft/in
9'8" 9'8" 10'2" 9'8" 9'8" 10'2"
Reach
at
Full
Lift
mm
1434 1434 1294 1434 1434 1294
and 45º Discharge (§)
ft/in
4'8" 4'8" 4'3" 4'8" 4'8" 4'3"
Reach with Lift Arm Horizontal
mm
2942
2942
2737
2942
2942
2737
and Bucket Level (§)
ft/in
9'8" 9'8" 9'0" 9'8" 9'8" 9'0"
Digging Depth (§)
mm
78 108 108 78 108 108
in
3.07 4.25 4.25 3.07 4.25 4.25
Overall
Length
mm
9080 9080 8855 9080 9080 8855
ft/in
29'9" 29'9" 29'1" 29'9" 29'9" 29'1"
Overall
Height
with
Bucket
mm
5853 5853 5853 5853 5853 5853
at
Full
Raise
ft/in
19'2" 19'2" 19'2" 19'2" 19'2" 19'2"
Loader Clearance Circle with
mm
14 778
14 778
14 572
14 924
14 924
14 720
Bucket in Carry Position (§)
ft/in
48'6" 48'6" 47'10" 49'0" 49'0" 48'3"
Static Tipping Load Straight *
kg
17 655
17 196
17 382
17 567
17 178
17 394
lb
38,929
37,917
38,327
38,735
37,877
38,354
Static Tipping Load
kg
15 626
15 286
15 472
15 631
15 258
15 474
Full 37º Turn
lb
34,455
33,706
34,116
34,466
33,644
34,120
Breakout Force ** (§)
kN
200
186
188
200
186
188
lb
45,000
41,850
42,300
45,000
41,850
42,300
Operating Weight * (§)
kg
23 610
23 762
23 622
23 674
23 865
23 698
lb
52,060
52,395
52,087
52,201
52,622
52,254
(§) Specifications and ratings conform to all applicable standards recommended by the Society of Automotive Engineers, including SAE Standard J732C
governing loader ratings.
* Static tipping loads and operating weights shown are based on standard machine configuration with 26.5R25 L-4 Firestone tires, roading fenders. powertrain
guard, full fuel tank, coolants, lubricants, air conditioner and operator.
** Measured 102 mm (4.0") behind tip of cutting edge with bucket hinge pin as pivot point in accordance with SAE J732C.