Zoom 8080 - Manual (Page 59)

This module contains conventional modulation-type effects such as flanger and chorus.
Characteristic flanger effect indispensable for jet sound.
Recreates a vintage flanger effect that has been extensively used by hard rock musicians.
Phaser effect which allows detailed manual settings.
This chorus effect lends body and ambience to the sound. The tonal quality of the effect can also be adjusted, to achieve a
warm chorus sound.
CHO: Chorus 1
PHA: Phaser 2
VFLG: Vintage Flanger 2
FLG: Flanger 1
■ 58
Effect
Types
and
Parameters
COMP EFF1 DIST EQ EFF2 EFF3 DLY REV TOTAL
EFF3 Module
UTILITY
PAGE
VFLG DPT= SPD=
FB= MAN=
VFLG
RTMå DIR=
3 4
1 2
MAX MIN
MAX MIN MAX MIN
MAX MIN
q w
e r
3 4
1 2
MAX MIN
MAX MIN MAX MIN
MAX MIN
t y
PAGE 1
PAGE 2
q w
e r
t y
q DPT (Depth) Sets the depth of the flanging effect. 0 – 50
w SPD (Speed) Sets the speed of the flanging effect. 1 – 100
e FB (Feedback) Increasing this parameter emphasizes modulation,
resulting in a more pronounced flanging effect. 0 – 10
r MAN (Manual) Sets the predelay time. 0 – 10
t RTM (RTM Destination) Shows which RTM parameter is being controlled. SPD
y DIR (RTM Direction) Sets the RTM direction. NML, INV
Parameters Comment Values
UTILITY
PAGE
PHA DPT= SPD=
RES= OFS=
PHA
RTM= DIR=
3 4
1 2
MAX MIN
MAX MIN MAX MIN
MAX MIN
q w
e r
3 4
1 2
MAX MIN
MAX MIN MAX MIN
MAX MIN
t y
PAGE 1
PAGE 2
q w
e r
t y
q DPT (Depth) Sets the depth of the phaser effect. 0 – 50
w SPD (Speed) Sets the speed of the phaser effect. 1 – 100
e RES (Resonance) Emphasizes the phaser effect. 0 – 10
r OFS (Offset) Sets the center frequency when no modulation is
applied.
0 – 10
t RTM (RTM Destination) Sets the parameter to be controlled by RTM. SPD, RES
y DIR (RTM Direction) Sets the RTM direction. NML, INV
Parameters Comment Values
UTILITY
PAGE
CHO DPT= SPD=
HiC= Mix=
CHO
RTMå DIR=
3 4
1 2
MAX MIN
MAX MIN MAX MIN
MAX MIN
q w
e r
3 4
1 2
MAX MIN
MAX MIN MAX MIN
MAX MIN
t y
PAGE 1
PAGE 2
q w
e r
t y
q DPT (Depth) Sets the depth of the phaser effect. 0 – 50
w SPD (Speed) Sets the speed of the phaser effect. 1 – 100
e HiC (High Cut) Causes a treble cut in the effect sound. 0 – 10
r Mix (Mix) Adjusts the balance between original sound and
effect sound.
0 – 100
t RTM (RTM Destination) Shows which RTM parameter is being controlled. Mix
y DIR (RTM Direction) Sets the RTM direction. NML, INV
Parameters Comment Values
UTILITY
PAGE
FLG DPT= SPD=
FB= MAN=
FLG
RTM= DIR=
3 4
1 2
MAX MIN
MAX MIN MAX MIN
MAX MIN
q w
e r
3 4
1 2
MAX MIN
MAX MIN MAX MIN
MAX MIN
t y
PAGE 1
PAGE 2
q w
e r
t y
q DPT (Depth) Sets the depth of the flanging effect 0 – 50
w SPD (Speed) Sets the speed of the flanging effect. 1 – 100
e FB (Feedback) Increasing this parameter emphasizes modulation,
resulting in a more pronounced flanging effect.
0 – 10
r MAN (Manual) Sets the predelay time. 0 – 10
t RTM (RTM Destination) Sets the parameter to be controlled by RTM. SPD, FB
y DIR (RTM Direction) Sets the RTM direction. NML, INV
Parameters Comment Values