Zoom 8080 - Manual (Page 53)

Recreates a popular vintage distortion effect with wild character.
Recreates a vintage distortion effect that took the world by storm: hard stacked-amp type distortion.
Recreates the archetypical fuzz sound.
VFzB: Vintage Fuzz B
VDSM: Vintage Distortion M
VDSP: Vintage Distortion P
■ 52
Effect
Types
and
Parameters
UTILITY
PAGE
VFzB SUS= EQ=
LVL= ZNR=
VFzB
RTMå DIR=
3 4
1 2
MAX MIN
MAX MIN MAX MIN
MAX MIN
q w
e r
3 4
1 2
MAX MIN
MAX MIN MAX MIN
MAX MIN
t y
PAGE 1
PAGE 2
q w
e r
t y
q SUS (Sustain) Sets the distortion type. 1 – 30
w EQ (EQ) Sets the tonal quality. Higher values emphasize
the treble range.
-10 – +10
e LVL (Level) Sets the output level. 1 – 16
r ZNR (ZNR) Sets the activation threshold for Zoom Noise Reduction
which suppresses noise during no-signal passages.
The key to effective use of ZNR is setting the value
as high as possible without causing the noise cutoff to
sound unnatural. ZNR can be used also when the
DIST module is off.
0ff, 1 – 10
t RTM (RTM Destination) Shows which RTM parameter is being controlled. SUS
y DIR (RTM Direction) Sets the RTM direction. NML, INV
Parameters Comment Values
UTILITY
PAGE
VDSP DST=
LVL= ZNR=
VDSP
RTMå DIR=
3 4
1 2
MAX MIN
MAX MIN MAX MIN
MAX MIN
q
w e
3 4
1 2
MAX MIN
MAX MIN MAX MIN
MAX MIN
r t
PAGE 1
PAGE 2
q
w
e
r t
q DST (Distortion) Sets the distortion type. 1 – 30
w LVL (Level) Sets the output level. 1 – 16
e ZNR (ZNR) Sets the activation threshold for Zoom Noise Reduction
which suppresses noise during no-signal passages.
The key to effective use of ZNR is setting the value
as high as possible without causing the noise cutoff to
sound unnatural. ZNR can be used also when the
DIST module is off.
0ff, 1 – 10
r RTM (RTM Destination) Shows which RTM parameter is being controlled. DST
t DIR (RTM Direction) Sets the RTM direction. NML, INV
Parameters Comment Values
UTILITY
PAGE
VDSM DST= TRE=
LVL= ZNR=
VDSM
RTMå DIR=
3 4
1 2
MAX MIN
MAX MIN MAX MIN
MAX MIN
q w
e r
3 4
1 2
MAX MIN
MAX MIN MAX MIN
MAX MIN
t y
PAGE 1
PAGE 2
q w
e r
t y
q DST (Distortion) Sets the distortion type. 1 – 30
w TRE (Treble) Adjusts the treble range. Higher values emphasize
the range and lower values cut the range.
-10 – +10
e LVL (Level) Sets the output level. 1 – 16
r ZNR (ZNR) Sets the activation threshold for Zoom Noise Reduction
which suppresses noise during no-signal passages.
The key to effective use of ZNR is setting the value
as high as possible without causing the noise cutoff to
sound unnatural. ZNR can be used also when the
DIST module is off.
0ff, 1 – 10
t RTM (RTM Destination) Shows which RTM parameter is being controlled. DST
y DIR (RTM Direction) Sets the RTM direction. NML, INV
Parameters Comment Values