VocoPro DTX-9909K - Manual (Page 41)

41
• MIC1 VOL (Microphone channel 1 volume)
Use this setting to set the maximum volume level for micro-
phone channel 1. NOTE: If this is set too low, the micro-
phone will not be loud enough.
Use the Input/Adjust knob on the front panel or the and
buttons on the remote control to adjust the maximum
volume for microphone channel 1.
Volume Range: 0 -- 80
1. Turn the Input/Adjust knob on the front panel clock-
wise or press the button on the remote control to
raise the volume.
2. Turn the Input/Adjust knob on the front panel counter-
clockwise or press the button on the remote control to
lower the volume.
• MIC2 VOL (Microphone channel 2 volume)
Use this setting to set the maximum volume level for micro-
phone channel 2. NOTE: If this is set too low, the micro-
phone will not be loud enough.
Use the Input/Adjust knob on the front panel or the and
buttons on the remote control to adjust the maximum
volume for microphone channel 2.
Volume Range: 0 -- 80
1. Turn the Input/Adjust knob on the front panel clock-
wise or press the button on the remote control to
raise the volume.
2. Turn the Input/Adjust knob on the front panel counter-
clockwise or press the button on the remote control to
lower the volume.
• MIC BASS (Microphone bass tone level)
Use this setting to adjust the amount of bass tone that is
present in the microphone channels 1 and 2.
Use the Input/Adjust knob on the front panel or the and
buttons on the remote control to adjust the microphone
bass tone level.
Bass Tone Range: -10dB -- +10dB Bass Tone Range: -10dB -- +10 Bass Tone Range: -10dB -- +10
1. Turn the Input/Adjust knob on the front panel clock-
wise or press the button on the remote control to
increase the bass.
2. Turn the Input/Adjust knob on the front panel counter-
clockwise or press the button on the remote control
decrease the bass.
• MIC TREB (Microphone Treble tone level)
Use this setting to adjust the amount of treble that is pres-
ent in the microphone channels 1 and 2.
Use the Input/Adjust knob on the front panel or the and
buttons on the remote control to adjust the microphone
treble level.
Treble Tone Range: -10dB -- +10dB Treble Tone Range: -10dB -- +10 Treble Tone Range: -10dB -- +10
1. Turn the Input/Adjust knob on the front panel clock-
wise or press the button on the remote control to
increase the treble.
2. Turn the Input/Adjust knob on the front panel counter-
clockwise or press the button on the remote control
decrease the treble.
• MIC DELAY (Microphone Echo/Delay Effect)
Use this setting to set the delay time for the DSP micro-
phone echo effect.
NOTE: The DSP effect volume must be set loud enough in
order to hear the effect
Use the Input/Adjust knob on the front panel or the and
buttons on the remote control to adjust the delay time.
Delay Time Range: 0ms -- 250ms
1. Turn the Input/Adjust knob on the front panel clock-
wise or press the button on the remote control to
increase the delay time.
2. Turn the Input/Adjust knob on the front panel counter-
clockwise or press the button on the remote control
decrease the delay time.
• REPEAT (Microphone Echo/Repeat Effect)
Use this setting to set the amount of repeat for the DSP
microphone echo effect.
NOTE: The DSP effect volume must be set loud enough in
order to hear the effect
Use the Input/Adjust knob on the front panel or the and
buttons on the remote control to adjust repeat level.
Repeat Range: 0dB -- 0dB 0dB 80dB
1. Turn the Input/Adjust knob on the front panel clock-
wise or press the button on the remote control to
increase the repeat level.
2. Turn the Input/Adjust knob on the front panel counter-
clockwise or press the button on the remote control
decrease the repeat level.
Karaoke Mode cont.