Functions of the system parameters, Settings common to the entire system (general), Settings related to controllers (controller) – Roland JUNO-D User Manual

Page 89: Mod (modulation assign), P. 89), Make settings common to the entire system (p. 89), Make controller-related settings (p. 89), 89 settings common to all modes (system function)

Settings common to all modes (System Function)

System Function

Functions of the system

parameters

System parameter functions are explained here according to the
group in which they are found.

Settings common to the entire

system (GENERAL)

LCD Contrast

Adjusts the contrast of the display.

VALUE:

1–10

The LCD CONTRAST setting is saved automatically, and is
retained even while the power is off.

Master Tune

Adjusts the overall tuning of the JUNO-D. The display shows the
frequency of the A4 note (center A).

VALUE:

415.3–466.2 Hz

Master Key Sft (Master Key Shift)

Shifts the overall pitch of the JUNO-D in semitone steps.

VALUE:

-24–+24

Master Level

Adjusts the volume of the entire JUNO-D.

VALUE:

0–127

Hold Pedal (Hold Pedal Polarity)

Select the polarity of the Hold pedal. On some pedals, the electrical
signal output by the pedal when it is pressed or released is the
opposite of other pedals. If your pedal has an effect opposite of what
you expect, set this parameter to “REVERSE.” If you are using a
Roland pedal (that has no polarity switch), set this parameter to
“STANDARD.”

VALUE:

STANDARD, REVERSE

Local Control (Local Controller)

The Local Controller determines whether the internal sound
generator is disconnected (OFF) from the keyboard controller section
(keyboard, pitch bend/modulation lever, knobs, buttons, D Beam
controller, pedal, and so on); or not disconnected (ON). Normally,
this is left “ON”, but if you wish to use the JUNO-D’s keyboard and
controllers to control only external sound modules, set it to “OFF.”

VALUE:

OFF, ON

Clock Source

Select “MIDI” if you want synchronization-related MIDI messages to
be received from an external sequencer. Select “INT” if you want to
synchronize to the JUNO-D’s internal tempo. The multi-effect
changes will also synchronize to this setting.

VALUE:

INT, MIDI

Settings related to controllers

(CONTROLLER)

Mod (Modulation Assign)

You can use the modulation lever to apply the following effects
other than vibrato.

In Patch mode, the modulation lever will affect the patch. In
Performance mode, the modulation lever will affect the patch that is
assigned to the current part. Use [DESTINATION TONE] to specify
the tone that will be affected (p. 26).

“TxCC#” refers to the controller number of the control change
message sent from the MIDI OUT connector when the modulation
lever is operated. When set to AFTERTOUCH, Channel Aftertouch
messages are sent. Set to AFTERTOUCH mainly when you want to
control an external sound generator with Aftertouch messages.

Receiving these control change message from the MIDI IN connector
produces the same effect as operating the modulation lever.

* When set to MFX PARAMETER1 or MFX PARAMETER2, be sure

to note the following.

• When the multi-effects Type is set to 01: STEREO EQ (p. 69) or 42:

LOFI (p. 83), Level is changed regardless of whether MFX
PARAMETER1 or MFX PARAMETER2 is selected.

* When making the LFO RATE, LFO DEPTH or LFO DELAY settings,

the effect achieved differs depending on whether [FILTER LFO] is on or
off. When [FILTER LFO] is off, the LFO alters the pitch (vibrato
effect). When [FILTER LFO] is on, the LFO changes the Filter Cutoff
frequency (wah effect).

Value

Tx CC#

Function/Parameter
Changed

MODULATION

CC01

Vibrato

PORTA TIME

CC05

Portamento Time (p. 47)

VOLUME

CC07

Level