Roland JUNO-D - Manual (Page 82)

82
Adding effects
36: CHORUS>DELAY
This effect connects a chorus and a delay unit in series.
fig.MFX-36
37: FLG>DELAY (Flanger → Delay)
This effect connects a flanger and a delay in series.
fig.MFX-37
Parameter Value Description
Cho Delay 0.0–100 [ms] Adjusts the time delay from
when the direct sound begins
until the chorus sound is heard.
Cho Rate 0.05–10.00 [Hz] Adjusts the modulation speed of
the chorus effect.
Cho Depth 0–127 Adjusts the modulation depth of
the chorus effect.
Cho Balance # D100:0W–
D0:100W Adjusts the volume balance be-
tween the direct sound and the
chorus sound.
With a setting of “D100:0W,”
only the direct sound will be
output. With a setting of
“D0:100W,” only the chorus
sound will be output.
Delay Time 0–500 [ms] Adjusts the time delay from
when the direct sound begins
until the delay sound is heard.
Dly Feedback -98– +98 [%] Adjusts the proportion (%) of
the delay sound that is fed back
into the delay input.
Negative (-) settings will invert
the phase.
Dly HF Damp 200–8000 [Hz],
BYPASS Adjusts the frequency above
which delayed sound fed back
to the delay input will be cut.
If you do not want to cut the
high frequencies of the feed-
back, set this parameter to BY-
PASS.
Dly Balance # D100:0W–
D0:100W Adjusts the volume balance be-
tween the chorus sound that is
sent through the delay and the
chorus sound that is not sent
through the delay.
With a setting of “D100:0W,”
only the chorus sound will be
output. With a setting of
“D0:100W,” only the chorus
sound that is sent through the
delay will be output.
Level 0–127 Adjusts the output level.
Feedback
Delay
L in
R in
L out
R out
Balance W
Balance W
Balance D
Balance D
Chorus
Balance W
Balance W
Balance D
Balance D
Parameter Value Description
Flg Delay 0.0–100 [ms] Adjusts the time delay from
when the direct sound begins
until the flanger sound is heard.
Flg Rate 0.05–10.00 [Hz] Adjusts the modulation speed of
the flanger effect.
Flg Depth 0–127 Adjusts the modulation depth of
the flanger effect.
Flg Feedback -98– +98 [%] Adjusts the proportion (%) of
the flanger sound that is fed
back into the effect.
Negative (-) settings will invert
the phase.
Flg Balance # D100:0W–
D0:100W Adjusts the volume balance be-
tween the direct sound and the
flanger sound.
With a setting of “D100:0W,”
only the direct sound will be
output. With a setting of
“D0:100W,” only the flanger
sound will be output.
Delay Time 0–500 [ms] Adjusts the time delay from
when the direct sound begins
until the delay sound is heard.
Dly Feedback -98– +98 [%] Adjusts the proportion (%) of
the delay sound that is fed back
into the delay input.
Negative (-) settings will invert
the phase.
Dly HF Damp 200–8000 [Hz],
BYPASS Adjusts the frequency above
which delayed sound fed back
to the delay input will be cut.
If you do not want to cut the
high frequencies of the delay
feedback, set this parameter to
BYPASS.
Dly Balance # D100:0W–
D0:100W Adjusts the volume balance be-
tween the flanger sound that is
sent through the delay and the
flanger sound that is not sent
through the delay.
With a setting of “D100:0W,”
only the flanger sound will be
output. With a setting of
“D0:100W,” only the flanger
sound that is sent through the
delay will be output.
Level 0–127 Adjusts the output level.
Feedback
Delay
L in
R in
L out
R out
Balance W
Balance W
Balance D
Balance D
Flanger
Balance W
Balance W
Balance D
Balance D
Feedback
JUNO-D_e.book 82 ページ ２００４年６月１１日 金曜日 午後１時２１分